where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

344 views
Technical Discussions
Jignesh Dhimar
NDT Inspector,
LMATS, Australia, Joined Apr 2015, 4

Jignesh Dhimar

NDT Inspector,
LMATS,
Australia,
Joined Apr 2015
4
07:59 Aug-23-2019
Finding Debonding between composites

Hello All,

Could anyone help me out with below mentioned two different cases

Case I- Sandwich structure made of Carbon Steel (CS-5 mm) + Polyurethane (PU-10 mm) + Carbon Fibre (CF-10mm). is there any practical solution to find debonding(planner or volumetric) between Interface 1(CS-PU) and Interface 2 (PU-CF).
Access for UT from only one side (Carbon steel side)

Case II- Sandwich structure made of CF (15 mm)+ PU(15mm) + CF (10 mm).
Same finding as Case I.
Access from only one side.

 
 Reply 
 
Wiesław Bicz
Engineering,
PBP Optel sp. z o.o., Poland, Joined Feb 2009, 276

Wiesław Bicz

Engineering,
PBP Optel sp. z o.o.,
Poland,
Joined Feb 2009
276
10:37 Aug-23-2019
Re: Finding Debonding between composites
In Reply to Jignesh Dhimar at 07:59 Aug-23-2019 (Opening).

Immersion or contact testing should be possible in the first case, but it will be necessary to use transducer with quite short pulse and quite sophisticated signal analysis, since the difference between total reflection and transmission into plastic is not very strong and many internal reflexions in steel can be expected.
Second case is more difficult due to the fact, that CF and PU are not very different and CF is quite attenuating. It should work, but requires careful development of suitable procedures.

2
 
 Reply 
 
Anand
India, Joined Jul 2016, 1

Anand

India,
Joined Jul 2016
1
10:40 Aug-23-2019
Re: Finding Debonding between composites
In Reply to Jignesh Dhimar at 07:59 Aug-23-2019 (Opening).

Hi,
Myself Anand.

I think UT will work for composites.Based on my work experience I'm telling. But the combination of metal and composites, I am not sure.

Thanks.

1
 
 Reply 
 
Daniel Braun
Daniel Braun
12:49 Aug-23-2019
Re: Finding Debonding between composites
In Reply to Jignesh Dhimar at 07:59 Aug-23-2019 (Opening).

Generally it is possible, if you have the samples available - you may ship them to Sonotron NDT A-Lab for performing the trials and laying out the necessary setup (instrument, probe, settings) - if you're interesting simply e-mail and we'll proceed further. The service is FOC

 
 Reply 
 
Andres Romero
NDT Inspector,
Spain, Joined Jul 2019, 13

Andres Romero

NDT Inspector,
Spain,
Joined Jul 2019
13
04:26 Aug-24-2019
Re: Finding Debonding between composites
In Reply to Jignesh Dhimar at 07:59 Aug-23-2019 (Opening).

zoom image



Hello, sorry for my English is not good.
If possible, by immersion. With squirt machine.
Several frequencies are needed.
 
 Reply 
 

Product Spotlight

Wireless TOFD scanner

Quick, accurate and highly reproducible welds testing. The System operates wirelessly and is compat
...
ible with any type of Windows based Laptop, Desktop or Tablet.
>

GEKKO - Portable Phased Array Testing with TFM in Real-Time

The portable phased array testing system GEKKO provides 64 parallel test channels. On creating testi
...
ng parameters the operator is assisted by the CIVA software. Due to its modular set-up the GEKKO instrument is suitable for operators of all skill levels.
>

High-performance Linear Phased Array Probes

Available to order from stock in a range of 5MHz – 7.5MHz and from 16 to 64 elements. Designed w
...
ith piezo-composite elements, Phoenix phased array probes provide high-resolution imaging to maximise sensitivity; accurate ultrasonic detection and sizing of defects in welds; and effective corrosion mapping. Housed in a rugged stainless steel case for on-site industrial NDT applications.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window