where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

328 views
Technical Discussions
Chandrasekhar
Welspun Corp, pipe manufacturing , India, Joined Mar 2019, 2

Chandrasekhar

Welspun Corp, pipe manufacturing ,
India,
Joined Mar 2019
2
17:15 Aug-23-2019
I have some small doubts in UT
Download

1. There are calibration v2 blocks of 1.5 hole and 5 me hole what is the reason behind it is it only for better sensitivity or there were any other reson

2. While doing range calibration with v2 block I observed these things with Einstein modsonic 2 that while we faced the probe from 25 radius end of we clearly observe the depth it will be shown as 8.5 but where we given the thickness of the material as more than 8.5 but in the same case if the thickness is below it changes the value either 2 to 4.5 . Why?

3.what is the weld geometry for a pipe especially for double v saw weld
Pipe,

4. Is it really necessary to add the reinforcement of I'd and od to thickness of the parent material in the case where we using N5 notches (example coil thickness 15 and reinforcement is 1.5+1.5 so is iit mandetary to add 3mm to job thickness or not) .

5.can anyone share me the actual cycle time calculation ( I have doubt of taking the dia of the crystal as 8 or 12 for (8*9 rectangular crystprobe)

For 5 one just tell me what is correct. As we are facing 8' crystal and doing so we need to consider only 8 or as a formula we need to use 12 .
Just see attached link for my reference material and find page 449-56 page https://inis.iaea.org › _PublicPDF
Web results
ultrasonic testing of materials at level 2 - International Nuclear Information

https://www.google.com/url?sa=t&source=web&rct=j&url=https://inis.iaea.org/collection/NCLCollectionStore/_Public/19/100/19100874.pdf&ved=2ahUKEwi4lemBpJnkAhXVgeYKHUPGA7IQFjAAegQIAxAB&usg=AOvVaw33fQxSLXw0tnOFXLgU09kv

 
 Reply 
 
Rahul
India, Joined Jul 2019, 6

Rahul

India,
Joined Jul 2019
6
20:27 Aug-23-2019
Re: I have some small doubts in UT
In Reply to Chandrasekhar at 17:15 Aug-23-2019 (Opening).

Hi,
Answer for your second question..
When thickness is 8.5 or above, it shows tk as 8.5 means sound waves actually reflect at that point.
When it's below 8.5, tk will get reduce.. as machine trigonometry thinks the waves passing in the full skip which is not happen.
Here in m/c set tk as 7. Now waves after 7mm tk will be considered as it travels in full skip. So you will get tk 5.5.


 
 Reply 
 

Product Spotlight

Ultrasonic Testing Immersion Tanks with Unmatched Scanning Features

TecScan’s non-destructive testing Ultrasonic Immersion Tanks & scanners are designed for high pe
...
rformance and demanding NDT testing applications. Our Scan3D™ line of High Precision Immersion Tanks are specifically designed for automated ultrasonic testing of complex composites parts used in aerospace and industrial applications.
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

Portable Ground Penetrating Radar - Proceq GP8000

The Proceq GP8000 portable ground penetrating radar instrument is the beginning of a new era in ND
...
T. The outstanding, patented ultra- wideband technology combined with a compact wireless probe delivers unmatched industry performance. Proceq GP8000 is the world’s first large-scale inspection solution that utilizes Augmented Reality in industrial applications.
>

Customized Probes and Transducers

With a strong development department and our own piezocomposite production, we accompany you from th
...
e first product idea to serial production. Our scientists are continuously researching new methods in the field of ultrasonic measurement technology. The progress achieved enables us to offer you optimal solutions.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window