where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
299 views
Technical Discussions
Chandrasekhar
Welspun Corp, pipe manufacturing , India, Joined Mar 2019, 2

Chandrasekhar

Welspun Corp, pipe manufacturing ,
India,
Joined Mar 2019
2
17:15 Aug-23-2019
I have some small doubts in UT
Download

1. There are calibration v2 blocks of 1.5 hole and 5 me hole what is the reason behind it is it only for better sensitivity or there were any other reson

2. While doing range calibration with v2 block I observed these things with Einstein modsonic 2 that while we faced the probe from 25 radius end of we clearly observe the depth it will be shown as 8.5 but where we given the thickness of the material as more than 8.5 but in the same case if the thickness is below it changes the value either 2 to 4.5 . Why?

3.what is the weld geometry for a pipe especially for double v saw weld
Pipe,

4. Is it really necessary to add the reinforcement of I'd and od to thickness of the parent material in the case where we using N5 notches (example coil thickness 15 and reinforcement is 1.5+1.5 so is iit mandetary to add 3mm to job thickness or not) .

5.can anyone share me the actual cycle time calculation ( I have doubt of taking the dia of the crystal as 8 or 12 for (8*9 rectangular crystprobe)

For 5 one just tell me what is correct. As we are facing 8' crystal and doing so we need to consider only 8 or as a formula we need to use 12 .
Just see attached link for my reference material and find page 449-56 page https://inis.iaea.org › _PublicPDF
Web results
ultrasonic testing of materials at level 2 - International Nuclear Information

https://www.google.com/url?sa=t&source=web&rct=j&url=https://inis.iaea.org/collection/NCLCollectionStore/_Public/19/100/19100874.pdf&ved=2ahUKEwi4lemBpJnkAhXVgeYKHUPGA7IQFjAAegQIAxAB&usg=AOvVaw33fQxSLXw0tnOFXLgU09kv

 
 Reply 
 
Rahul
India, Joined Jul 2019, 6

Rahul

India,
Joined Jul 2019
6
20:27 Aug-23-2019
Re: I have some small doubts in UT
In Reply to Chandrasekhar at 17:15 Aug-23-2019 (Opening).

Hi,
Answer for your second question..
When thickness is 8.5 or above, it shows tk as 8.5 means sound waves actually reflect at that point.
When it's below 8.5, tk will get reduce.. as machine trigonometry thinks the waves passing in the full skip which is not happen.
Here in m/c set tk as 7. Now waves after 7mm tk will be considered as it travels in full skip. So you will get tk 5.5.


 
 Reply 
 

Product Spotlight

Semi-Automated Phased Array Immersion System for Small Composite Parts

Turn-key semi-automated system as an improved and affordable solution for inspection of small comp
...
osite parts. Includes support table, immersion tank, scanner, PA instrument, PC, Analysis software, database, wedge management and other options.
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

Eddy Current inspection : RotoETscan Rotating Head

The rotating head RotoETscan detects the presence of longitudinal surface or sub surface defects a
...
t high speed. The rotating head is often installed directly on the production line. It is generally dedicated to the control of long products such as tubes, bars and wires, made of ferrous or non-ferrous material. It can also be used for inspection of small parts (billets).
>

MUSE Mobile Ultrasonic Equipment

The MUSE, a portable ultrasonic imaging system, was developed for in-field inspections of light-weig
...
ht structures. The MUSE consists of a motor-driven manipulator, a water circulation system for the acoustic coupling and a portable ultrasonic flaw detector (USPC 3010). The MUSE provides images of internal defects (A-, B-,C- and D-scan).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window