where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

295 views
Technical Discussions
Nafis
Nafis
15:09 Aug-21-2019
Lead Marker for RT

Hi guys,

i have a question whether there are other options other than lead marker for RT works..

i am wondering whether there is a type of pen(i literally mean pen) that contain lead inks/filler to replace the conventional lead markers that are widely used in this industry.

thanks in advance guys. cheers..

 
 Reply 
 
SF
SF
08:38 Aug-22-2019
Re: Lead Marker for RT
In Reply to Nafis at 15:09 Aug-21-2019 (Opening).

SFD

 
 Reply 
 
Matthias
NDT Inspector, CEO
Dreifeld Materialprüftechnik, Germany, Joined Sep 2005, 105

Matthias

NDT Inspector, CEO
Dreifeld Materialprüftechnik,
Germany,
Joined Sep 2005
105
10:40 Aug-22-2019
Re: Lead Marker for RT
In Reply to Nafis at 15:09 Aug-21-2019 (Opening).

I don't think so since its toxic.

 
 Reply 
 
Godfrey Hands
Consultant,
PRI Nadcap, United Kingdom, Joined Nov 1998, 307

Godfrey Hands

Consultant,
PRI Nadcap,
United Kingdom,
Joined Nov 1998
307
09:24 Aug-26-2019
Re: Lead Marker for RT
In Reply to Nafis at 15:09 Aug-21-2019 (Opening).

Hi,
I have seen radiographers use a typed or printed ID info on a transparent sheet, and the film when exposed to radiation has a small area (same size as the ID) covered with lead. After exposure to radiation, the film cassette was opened in the dark room and then the ID sheet was placed on the unexposed area and just that small ID bit exposed to light in a device.
This then transferred to ID info onto the film.

You have to be careful not to mix films up, but it is an alternative to using lead for ID.
You still need to use lead markers when testing larger areas with multiple shots (such as welds)


Godfrey

 
 Reply 
 

Product Spotlight

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

Micro CT

nanoVoxel series has nano-scale resolution upto 500nm by using high voltage X-ray source (from 80-
...
300 kV) with micro/nano focal spot and highly sensitive flat panel detectors and unique Optical coupling detector.
>

TESTD-PT SYSTEM

Pulse thermography is a non-contact test method that is ideal for the characterization of thin fil
...
ms and coatings or the detection of defects. With a remarquable short test time and a high detection sensitivity, the Telops TESTD-PT is the perfect tool for non- destructive testing. With such high frame rates, it is even possible to investigate highly conductive or diffusive materials.
>

High-performance Linear Phased Array Probes

Available to order from stock in a range of 5MHz – 7.5MHz and from 16 to 64 elements. Designed w
...
ith piezo-composite elements, Phoenix phased array probes provide high-resolution imaging to maximise sensitivity; accurate ultrasonic detection and sizing of defects in welds; and effective corrosion mapping. Housed in a rugged stainless steel case for on-site industrial NDT applications.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window