where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

YXLON Copenhagen
YXLON Copenhagen is a highly specialized, award winning Danish company with 60 years of experience in portable X-ray solutions for industrial NDT.

379 views
Career Discussions
Ricardo Andreucci
FATEC - Technological University of Sao Paulo, Brazil, Joined May 2018, 38

Ricardo Andreucci

FATEC - Technological University of Sao Paulo,
Brazil,
Joined May 2018
38
13:33 Aug-19-2019
NDE Level III Recertification

Dear Sirs.
According to ASME Code Sec.V Article 1 Appendix III 2019 Edition the recertification of NDE personnel Levels I, II and III shall be made by examination. Continuing satisfactory performance is no longer acceptable. But on the other hand this paragraph 12.1 of Appendix III do not specify which examination shall be applied (general, specific or practical) and also who should apply it. So, my question is can a NDE Level III be recertified by specific examination only , as described in your written practice ?
Thank you.

 
 Reply 
 
William A. Jensen
Other,
IHI Southwest Technologies, Inc., USA, Joined May 2017, 67

William A. Jensen

Other,
IHI Southwest Technologies, Inc.,
USA,
Joined May 2017
67
16:34 Aug-19-2019
Re: NDE Level III Recertification
In Reply to Ricardo Andreucci at 13:33 Aug-19-2019 (Opening).

Appendix III only applies to personnel using the 2016 Edition of ASNT SNT-TC-1A.

Having said that, if you are to be re-certified by examination, then the implied requirement would be that your examinations that took to be initially certified would have to be re-taken unless the base document (TC-1A) stated otherwise. For Level III, that would mean that you would have to take the method & specific again.

 
 Reply 
 
Ricardo Andreucci
FATEC - Technological University of Sao Paulo, Brazil, Joined May 2018, 38

Ricardo Andreucci

FATEC - Technological University of Sao Paulo,
Brazil,
Joined May 2018
38
21:20 Aug-28-2019
Re: NDE Level III Recertification
In Reply to William A. Jensen at 16:34 Aug-19-2019 .

Thanks Mr. William Jensen for your comment.
You may be correct, however, manufacturers using ASME Sec.VIII Div.1 2019 Ed. will have to transition between SNT-TC-1A Ed.2006 to Ed.2016 and Art. 1 Appendice III of ASME Sec.V 2019 Ed. from Jan.2020, for radiographic and ultrasonic testing methods.
I am not sure that a NDE Level III who has been working for years and now changing rules he would have to re-taken all examination again in order to recertified. In this point the Appendix III is not clear. In my opinion, this can be clarified in the Level III employer´s written practice.

 
 Reply 
 

Product Spotlight

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

NDT.net launches mobile-friendly design

NDT.net has revamped its website providing a mobile-friendly design.The front page received a comp
...
letely new design and all other sections are now reacting responsively on mobile devices. This has been a major step to make our website more user- friendly.
>

OPBOX with standard software is able to do all types of inspections and measurements: flaw detection in welds and materials, scanning of objects, testing composite materials, forged and moulded pieces, many UT inspections, measurements of properties of ma

Typical applications: UT measurements with pulse technique, Measurement of thicknesses also at hig
...
h temperatures, Measurements of properties of materials, including fluids and gases We are delivering a standard version of the software (for any Microsoft Windows up to 10 x64 with Microsoft Hardware certification report Approved) and for special needs: SDK with ready to use examples for LabView, MATLAB x64, C++ wrapper for dll, Python and Linux., and also low-level description of how to control our devices directly from any USB tools
>

IntraPhase Athena Phased Array System

The Athena Phased Array system, manufactured by WesDyne NDE Products & Technology, consists of a pha
...
sed array acquisition system and PC running IntraSpect software. A PC is used to perform acquisition, analysis and storage of the data. System hardware is capable of operating up to four data sets with any combination of phased array or conventional UT probes. NOW AVAILABLE IN 64-64 CONFIGURATION.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window