where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Matec Instrument Companies, Inc.
Ultrasonic test instrumentation and systems for scientific research, quality control inspection and production testing applications.
565 views
Technical Discussions
Nikos Roussos
Greece, Joined Aug 2019, 2

Nikos Roussos

Greece,
Joined Aug 2019
2
21:33 Sep-01-2019
PAUT inspection of thick welds
zoom image

weld

Dear experts,
I‘ve been asked if I can inspect properly welded pipes with thickness of 90mm.
The equipment that I have is a Sonatest Prisma 16:64 with X3-PE-5.0M64E0.6P 64 element probe. I will also use a weld scanner from Phoenix.
Do you think my equipment is capable of giving me reliable results in such thick welds with the geometry shown in the figure? Do you think I should get a sensor with less frequency (2,25 or 3,5 MHz)?
Additional to PAUT inspection I will also perform TOFD, but my main concerns are for the PAUT.

 
 Reply 
 
Creed
NDT Inspector,
n.n., Joined Jul 2009, 33

Creed

NDT Inspector,
n.n.,
Joined Jul 2009
33
06:15 Sep-02-2019
Re: PAUT inspection of thick welds
In Reply to Nikos Roussos at 21:33 Sep-01-2019 (Opening).

First of all, the inspection should be performed following the standard and acceptance criteria or your company procedure writing; follow the standard, I am pretty sure you will have the answer YES or NO for your question.
My opinion you need to conduct the inspection with multi scans to cover entire the weld body, however based on the sketch of weld configuration the bevel angle should be concerned as a limitation, due to oriental of the fusion face defects wouldn't give the good refection with the PAUT sectorial beam.

1
 
 Reply 
 
Elias Campanario
Engineering,
Tecnicas Reunidas, Spain, Joined Oct 2013, 3

Elias Campanario

Engineering,
Tecnicas Reunidas,
Spain,
Joined Oct 2013
3
10:22 Sep-02-2019
Re: PAUT inspection of thick welds
In Reply to Nikos Roussos at 21:33 Sep-01-2019 (Opening).

Dear Nikos;

Regarding your question, in my opinion, the best solution in your case would be to combine inspection by ToFD and PAUT.

In any case, you should make a mock up with notches in the welding bevel, in which to test the scan plan that you generate for the inspection.

As for the PAUT probes, maybe for that thickness you need a 3.5 or 2.25 MHz probe.
With the 5MHz probe, maybe you to have a lot of noise at great depth.

I hope I've helped.

1
 
 Reply 
 
Ali
NDT Inspector,
Iran, Joined Mar 2013, 105

Ali

NDT Inspector,
Iran,
Joined Mar 2013
105
15:39 Sep-02-2019
Re: PAUT inspection of thick welds
In Reply to Nikos Roussos at 21:33 Sep-01-2019 (Opening).

this bevel configuration is not suitable for PAUT Sectorial scan but you can apply Tofd for better detection of side wall defect.If you have access to inside of vessel,perform Tofd and PAUT scan from out side and inside ( only half skip for PAUT) .this technique will reduce tofd dead zone only in backwall area and for PAUT will reduce sound path and increase signal to nois ratio in half skip instead of full skip scan.
Hope material grains is fine and surface is not wrought for PAUT and Tofd inspection.

1
 
 Reply 
 
laurie
Australia, Joined Feb 2019, 34

laurie

Australia,
Joined Feb 2019
34
02:35 Sep-03-2019
Re: PAUT inspection of thick welds
In Reply to Nikos Roussos at 21:33 Sep-01-2019 (Opening).

If you're going to be doing more of this type of work I'd suggest your boss might have to stump up for some simulation software.

Use a simulator like UTMan which from memory is something like 100 Euro and does manual UT, TOFD and AUT.
http://www.utsim.co.uk/index.html

If you have a couple of thousand dollars then Beamtools will do everything and also has sectorial beamset beam energy display which would be a big help for your long beam paths.
https://www.eclipsescientific.com/beamtool.html

There are lots of others including Olympus NDT SetupBuilder
https://www.olympus-ims.com/en/omniscan-software/#!cms[tab]=%2Fomniscan-software%2Fndt-setupbuilder

 
 Reply 
 

Product Spotlight

NEW Wheel Type Phased Array Probe

DOPPLER NEW Wheel Type Phased Array Probe, more stable, new tyre makes lesser acoustic attenuation
...
, much lighter makes easier to handle, more slim size, magnetic and mechanical encoder optional etc...more
>

MIZ®-21C: Truly Affordable Eddy Current Handheld with Surface Array Capability

Introducing MIZ-21C, the first truly affordable handheld eddy current instrument with surface array
...
capabilities. MIZ-21C can deliver fast, accurate inspections in demanding NDT applications including aerospace, oil and gas, manufacturing, and power generation. The surface array solution can reduce inspection time by up to 95% compared to traditional handheld pencil probes. The ergonomic design, long battery life, and intuitive touchscreen mean you can inspect more areas faster than ever without fatigue.
>

NDTkit RT

NDTkit RT, TESTIA's Digital Radiography software The NDTkit product line software for X-ray analysi
...
s. NDTkit RT is a software benefiting from the Ultis kernel which is dedicated to radiographic image analysis. It offers a set of tools and filtering processes to assist RT operators in finding relevant flaws.
>

Eddy Current inspection : RotoETscan Rotating Head

The rotating head RotoETscan detects the presence of longitudinal surface or sub surface defects a
...
t high speed. The rotating head is often installed directly on the production line. It is generally dedicated to the control of long products such as tubes, bars and wires, made of ferrous or non-ferrous material. It can also be used for inspection of small parts (billets).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window