where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

370 views
Technical Discussions
Raheel
NDT Inspector,
Pakistan, Joined Sep 2013, 14

Raheel

NDT Inspector,
Pakistan,
Joined Sep 2013
14
06:01 Sep-05-2019
urgent help required regarding Signal Acquisition problem in MS5800 ET equipment

Hello everyone!

We are using MS-5800 ET equipment for last 10 years but facing this problem for the first time. When we start data acquisition, it doesn't display the real signal rather a continuous straight line is appearing on strip chart. Moreover, there is no change on lissajous window. We have tried with different probes but the same issue sustains. Also, for RFT the same thing happen. One more thing, all the LEDs are working properly except VDC. Kindly guide what can be the reason/s and also suggest some solution. Waiting for your replies.
Thank you.

 
 Reply 
 
Clinton Raja
,
India, Joined Aug 2019, 2

Clinton Raja

,
India,
Joined Aug 2019
2
10:21 Sep-05-2019
Re: urgent help required regarding Signal Acquisition problem in MS5800 ET equipment
In Reply to Raheel at 06:01 Sep-05-2019 (Opening).

Once reinstall the multiview software and try again. Otherwise check the continuity of the probe using multi meter. Straight lines are coming due to the discontinuity in probe connectors.

Thanks and regards

Clinton Raja
8122110125

 
 Reply 
 
Raheel Zia
NDT Inspector,
Pakistan, Joined Sep 2013, 14

Raheel Zia

NDT Inspector,
Pakistan,
Joined Sep 2013
14
06:28 Sep-06-2019
Re: urgent help required regarding Signal Acquisition problem in MS5800 ET equipment
In Reply to Clinton Raja at 10:21 Sep-05-2019 .

Thank you Raja for replying.
I have already tried both of options suggested by you. Also, tried with different ET probes but the problem sustains. :(

 
 Reply 
 
Clinton Raja
,
India, Joined Aug 2019, 2

Clinton Raja

,
India,
Joined Aug 2019
2
06:55 Sep-06-2019
Re: urgent help required regarding Signal Acquisition problem in MS5800 ET equipment
In Reply to Raheel Zia at 06:28 Sep-06-2019 .

When you open the multiview software, is it showing green signal? Or it's showing yellow? If it's not showing, try to troubleshoot the boot manager.

 
 Reply 
 
Raheel Zia
NDT Inspector,
Pakistan, Joined Sep 2013, 14

Raheel Zia

NDT Inspector,
Pakistan,
Joined Sep 2013
14
07:13 Sep-06-2019
Re: urgent help required regarding Signal Acquisition problem in MS5800 ET equipment
In Reply to Clinton Raja at 10:21 Sep-05-2019 .

Thank you Raja for replying.
I have already tried both of options suggested by you. Also, tried with different ET probes but the problem sustains. :(

 
 Reply 
 
Raheel Zia
NDT Inspector,
Pakistan, Joined Sep 2013, 14

Raheel Zia

NDT Inspector,
Pakistan,
Joined Sep 2013
14
07:20 Sep-06-2019
Re: urgent help required regarding Signal Acquisition problem in MS5800 ET equipment
In Reply to Clinton Raja at 06:55 Sep-06-2019 .

It is showing green light. I think it is ok with boot configuration.

 
 Reply 
 
Anmol Birring
Consultant,
Birring NDE Center, Inc., USA, Joined Aug 2011, 833

Anmol Birring

Consultant,
Birring NDE Center, Inc.,
USA,
Joined Aug 2011
833
23:37 Sep-07-2019
Re: urgent help required regarding Signal Acquisition problem in MS5800 ET equipment
In Reply to Raheel Zia at 07:20 Sep-06-2019 .

I think you have hardware issues with MS 5800

 
 Reply 
 

Product Spotlight

Eddy Current inspection : RotoETscan Rotating Head

The rotating head RotoETscan detects the presence of longitudinal surface or sub surface defects a
...
t high speed. The rotating head is often installed directly on the production line. It is generally dedicated to the control of long products such as tubes, bars and wires, made of ferrous or non-ferrous material. It can also be used for inspection of small parts (billets).
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

Micro CT

nanoVoxel series has nano-scale resolution upto 500nm by using high voltage X-ray source (from 80-
...
300 kV) with micro/nano focal spot and highly sensitive flat panel detectors and unique Optical coupling detector.
>

IRIS 9000Plus - Introducing the next generation of heat exchanger inspection.

Representing the seventh generation of the IRIS system, the IRIS 9000 Plus has nearly 200 years of c
...
ombined field inspection experience incorporated in its design. This experience combined with a strong commitment to quality and a history of innovation has made Iris Inspection Services® the undisputed leader in IRIS technology.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window