where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
320 views
Technical Discussions
Raheel
NDT Inspector,
Pakistan, Joined Sep 2013, 14

Raheel

NDT Inspector,
Pakistan,
Joined Sep 2013
14
06:01 Sep-05-2019
urgent help required regarding Signal Acquisition problem in MS5800 ET equipment

Hello everyone!

We are using MS-5800 ET equipment for last 10 years but facing this problem for the first time. When we start data acquisition, it doesn't display the real signal rather a continuous straight line is appearing on strip chart. Moreover, there is no change on lissajous window. We have tried with different probes but the same issue sustains. Also, for RFT the same thing happen. One more thing, all the LEDs are working properly except VDC. Kindly guide what can be the reason/s and also suggest some solution. Waiting for your replies.
Thank you.

 
 Reply 
 
Clinton Raja
,
India, Joined Aug 2019, 2

Clinton Raja

,
India,
Joined Aug 2019
2
10:21 Sep-05-2019
Re: urgent help required regarding Signal Acquisition problem in MS5800 ET equipment
In Reply to Raheel at 06:01 Sep-05-2019 (Opening).

Once reinstall the multiview software and try again. Otherwise check the continuity of the probe using multi meter. Straight lines are coming due to the discontinuity in probe connectors.

Thanks and regards

Clinton Raja
8122110125

 
 Reply 
 
Raheel Zia
NDT Inspector,
Pakistan, Joined Sep 2013, 14

Raheel Zia

NDT Inspector,
Pakistan,
Joined Sep 2013
14
06:28 Sep-06-2019
Re: urgent help required regarding Signal Acquisition problem in MS5800 ET equipment
In Reply to Clinton Raja at 10:21 Sep-05-2019 .

Thank you Raja for replying.
I have already tried both of options suggested by you. Also, tried with different ET probes but the problem sustains. :(

 
 Reply 
 
Clinton Raja
,
India, Joined Aug 2019, 2

Clinton Raja

,
India,
Joined Aug 2019
2
06:55 Sep-06-2019
Re: urgent help required regarding Signal Acquisition problem in MS5800 ET equipment
In Reply to Raheel Zia at 06:28 Sep-06-2019 .

When you open the multiview software, is it showing green signal? Or it's showing yellow? If it's not showing, try to troubleshoot the boot manager.

 
 Reply 
 
Raheel Zia
NDT Inspector,
Pakistan, Joined Sep 2013, 14

Raheel Zia

NDT Inspector,
Pakistan,
Joined Sep 2013
14
07:13 Sep-06-2019
Re: urgent help required regarding Signal Acquisition problem in MS5800 ET equipment
In Reply to Clinton Raja at 10:21 Sep-05-2019 .

Thank you Raja for replying.
I have already tried both of options suggested by you. Also, tried with different ET probes but the problem sustains. :(

 
 Reply 
 
Raheel Zia
NDT Inspector,
Pakistan, Joined Sep 2013, 14

Raheel Zia

NDT Inspector,
Pakistan,
Joined Sep 2013
14
07:20 Sep-06-2019
Re: urgent help required regarding Signal Acquisition problem in MS5800 ET equipment
In Reply to Clinton Raja at 06:55 Sep-06-2019 .

It is showing green light. I think it is ok with boot configuration.

 
 Reply 
 
Anmol Birring
Consultant,
Birring NDE Center, Inc., USA, Joined Aug 2011, 786

Anmol Birring

Consultant,
Birring NDE Center, Inc.,
USA,
Joined Aug 2011
786
23:37 Sep-07-2019
Re: urgent help required regarding Signal Acquisition problem in MS5800 ET equipment
In Reply to Raheel Zia at 07:20 Sep-06-2019 .

I think you have hardware issues with MS 5800

 
 Reply 
 

Product Spotlight

Research and Application Development For NDT

Acuren’s Research and Application Development specializes in the development of advanced ultraso
...
nic inspection techniques and systems for challenging inspection applications, with an emphasis on practical solutions which are field deployable. Services include manual and automated ultrasonic inspection system development, inspection technique optimization using laboratory scale studies and ultrasonic modeling (CIVA, BeamTool), preparing technical justification for technique evaluation and qualification (Probability of Detection and sizing accuracy studies), inspection/calibration/analysis procedure preparation to support field deployment of custom techniques, and development of custom imaging algorithms to support challenging inspection applications.
>

iProbe - USB Phased Array Probe

Turn your PC, Laptop or Tablet into a powerful 32:64 Phased Array system with our USB powered Phas
...
ed Array iProbe and inspection software package. Perform affordable weld inspection and corrosion mapping inspections with this powerful but small system. The probe has a 100V pulser, 8K PRF, dual axis encoder input and achieves outstanding signal quality.
>

Ultrasonic Probe Recharacterization Service

NDT Systems offers a comprehensive Aftercare and Recharacterization Service for all our ultrasonic
...
probes. The Recharacterization Service is fully compliant with International ASTM E1065 Standard Guide (and other applicable standards) and offers complete documentation, traceable to the ASTM E1065 Standard. For more details or to schedule Recharacterization Services contact ndtsales@ndtsystems.com
>

Cygnus 6+ PRO Multi-Mode Ultrasonic Thickness Gauge

The Cygnus 6+ PRO thickness gauge is the most advance gauge within the Cygnus range with key featu
...
res including: comprehensive data logging; A-scan and B-scan display; manual gain control; Bluetooth connectivity; and much more. With its unique dual display and three measuring modes (Multiple-Echo, Echo-Echo and Single-Echo), this surface thickness gauge offers maximum versatility for inspections.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window