where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

387 views
Technical Discussions
John O connell
,
Ireland, Joined Sep 2019, 3

John O connell

,
Ireland,
Joined Sep 2019
3
00:44 Sep-09-2019
Ultrasonic test results

Hello,
I am new to this forum and recently started doing ndt. I am doing some UT on mild steel plates being welded by a robot. Plates are 20mm thickness, half v joint with metal backing. All the steel is blasted clean before welding. We are seeing indications in 2 or 3 areas per test piece, about 1500mm long. Indications are at different depths at 9 and 14mm from top. We get signals of -7 and -12dB over 20mm in length. Then the signal drops away again. We are checking with the 60 and 70 degree probes on a GE usm go. It looks like lack of fusion but quite small. We cannot see it with a macro or grinding into it and looking with MPI. Our welders are asking how the robot is not putting in the same parameters the entire length especially as the fit up is tight. Is there a way we can prove the lof is there?

 
 Reply 
 
THAPS MELIH
NDT Inspector,
heavy engineering and shipbuilding kuwait, India, Joined Feb 2017, 24

THAPS MELIH

NDT Inspector,
heavy engineering and shipbuilding kuwait,
India,
Joined Feb 2017
24
06:02 Sep-09-2019
Re: Ultrasonic test results
In Reply to John O connell at 00:44 Sep-09-2019 (Opening).

ONE THING FIRST U TELL THAT IS FULL PENETRATION JOINT OR PARTIAL PENETRATION JOINT. IF IT IS PARTIAL PENETRATION MEANS THAT PROBLEM IS COMES AGAIN AND AGAIN . IF U NEED TO RECTIFY THAT PROBLEM U CAN GO FOR BACKGRINDING AND THEN DO DP TEST AND AGAIN U MAKE WELDING ON REVERSE SIDE ... I AM IN THE PROJECT OF CALMBUOY HERE ALSO SOME LIFTING BEAM ARE THERE AS U ALREADY SAID LIKE SAME JOINT CONFIGURATION .... WE ARE DOING LIKE THAT NOW WE DOEST NOT GET ANY INDICATION.(ALSO WAITING FOR EXPERT ANSWERS.....)

 
 Reply 
 
John
,
Ireland, Joined Sep 2019, 3

John

,
Ireland,
Joined Sep 2019
3
01:03 Sep-10-2019
Re: Ultrasonic test results
In Reply to THAPS MELIH at 06:02 Sep-09-2019 .

Thanks. It is a full penetration joint with metal backing. No root face on the chamfered side. One of my colleagues suggested it could be impurities in the rolled I beam edge making its way into the molten metal during welding and getting trapped, showing up as a lag of fusion during UT. Not sure how to prove, any suggestions?

 
 Reply 
 
John
,
Ireland, Joined Sep 2019, 3

John

,
Ireland,
Joined Sep 2019
3
01:05 Sep-10-2019
Re: Ultrasonic test results
In Reply to John at 01:03 Sep-10-2019 .

We cannot change to double v joint type, we can only weld from one side only because of the design

 
 Reply 
 
THAPS MELIH
NDT Inspector,
heavy engineering and shipbuilding kuwait, India, Joined Feb 2017, 24

THAPS MELIH

NDT Inspector,
heavy engineering and shipbuilding kuwait,
India,
Joined Feb 2017
24
05:46 Sep-10-2019
Re: Ultrasonic test results
In Reply to John at 01:03 Sep-10-2019 .

DEAR JOHN THANKS FOR THE REPLY , NO ISSUE U CAN AVOID THAT IMPURITIES PROBLEM ALSO .... U HAVE TO CLEAN THE WELD EACH PASS OF THE WELDING PROVIDE GRINDING AND THEN U FIRST SEE THE WHAT KIND OF WELDING MATERIAL U USED BECOZ SOME OF THEM SEE THE COST WISE SO THEY USE NOT A QUALITY WELDING MATERIAL . AND THEN USE CORRECT VOLTAGE FOR FUSION OF METAL.

 
 Reply 
 

Product Spotlight

PAUT Probes

Typical Phased Array probes have frequencies between 1MHz and 20MHz and the number of wafers is 10
...
to 128. M2 Electronics offers customers conventionally ultrasound probes and the ability to provide high-precision Phased Array Ultrasound Probes of up to 256 wafers. We can also customize the probe for our customers to meet the specific application requirements of the user.
>

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

Scatter Correction for Industrial Cone-Beam Computed Tomography (CBCT)

Download our white paper on Scatter Correction for Industrial Cone-Beam Computed Tomography (CBCT)
...
Using 3D VSHARP, a fast GPU-Based Linear Boltzmann Transport Equation Solver here: http://bit.ly/2Y0t78P
>

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window