where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

426 views
Career Discussions
Ashish
India, Joined Aug 2016, 5

Ashish

India,
Joined Aug 2016
5
14:58 Sep-10-2019
NAS 410 Aviation Standard NDT work procedure

Looking for help to have NDT work procedure as per EN 4179 AND NAS-410.
If any one can give a guide will be good help.
advancendts@gmail.com i will be available on this email.

Ash

 
 Reply 
 
Godfrey Hands
Consultant,
PRI Nadcap, United Kingdom, Joined Nov 1998, 307

Godfrey Hands

Consultant,
PRI Nadcap,
United Kingdom,
Joined Nov 1998
307
09:57 Sep-16-2019
Re: NAS 410 Aviation Standard NDT work procedure
In Reply to Ashish at 14:58 Sep-10-2019 (Opening).

Ash,
The general idea is that you write your own version to your own requirements.
These two documents are the same, line for line, so it is not necessary to have both documents.

The text in these two documents is very useful to copy, but be certain that you read carefully what you are saying (example in several places it says "When required by the written practice.....". here you should decide if it is a requirement or not, and if it is a requirement, say so, but if not, do not mention it)

If you do not use a certain level of operator (e.g. Level 1 Limited), then you do not have to include this level in your document (exception is Level 3. You must define L3 requirements)
The training and experience hours shown in the document are mandatory minimum amounts. You can decide to use more, but you may not decide to use less.

Another useful document is Nadcap checklist AC7114 section 5.

Hope that helps.

Godfrey

 
 Reply 
 
Rafid O. Lopez
, NDT Level 3
Mexico, Joined Jan 2010, 87

Rafid O. Lopez

, NDT Level 3
Mexico,
Joined Jan 2010
87
18:34 Sep-17-2019
Re: NAS 410 Aviation Standard NDT work procedure
In Reply to Ashish at 14:58 Sep-10-2019 (Opening).

Ashis

My recomendation is, use an EN4179 Level 3 for this purpose; some times the company need pay to have this service, a procedure alone is the same as NAS410 Standard alone; what you need is the Level 3 signature.

The standard and the procedure shall be almost the same in content. Remember with EN4179 you will need a RESPONSIBLE LEVEL 3, designated by the employer.

If you have specific questions, the best practice is use an EN4179 Level 3.

 
 Reply 
 

Product Spotlight

Scatter Correction for Industrial Cone-Beam Computed Tomography (CBCT)

Download our white paper on Scatter Correction for Industrial Cone-Beam Computed Tomography (CBCT)
...
Using 3D VSHARP, a fast GPU-Based Linear Boltzmann Transport Equation Solver here: http://bit.ly/2Y0t78P
>

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

VeeScan AirCraft Wheel Inspection

The VEESCAN offers maximum flexibility, has a proven mechanical design and records of breakdown-fr
...
ee operation of over 365 days. Appealing to companies in the Aerospace industry, the VEESCAN is ideal for all wheel-testing environments. With a wide selection of probes, the VeeScan allows your wheel testing facility the flexibility to select the most compatible configurations with their workload.
>

NDTkit RT

NDTkit RT, TESTIA's Digital Radiography software The NDTkit product line software for X-ray analysi
...
s. NDTkit RT is a software benefiting from the Ultis kernel which is dedicated to radiographic image analysis. It offers a set of tools and filtering processes to assist RT operators in finding relevant flaws.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window