where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

AT-Automation Technology GmbH
AT -Automation Technology is a systems house for industrial image processing. AT offers thermographic ndt systems as well as high-speed 3D sensors.

425 views
Career Discussions
Ashish
India, Joined Aug 2016, 5

Ashish

India,
Joined Aug 2016
5
14:58 Sep-10-2019
NAS 410 Aviation Standard NDT work procedure

Looking for help to have NDT work procedure as per EN 4179 AND NAS-410.
If any one can give a guide will be good help.
advancendts@gmail.com i will be available on this email.

Ash

 
 Reply 
 
Godfrey Hands
Consultant,
PRI Nadcap, United Kingdom, Joined Nov 1998, 307

Godfrey Hands

Consultant,
PRI Nadcap,
United Kingdom,
Joined Nov 1998
307
09:57 Sep-16-2019
Re: NAS 410 Aviation Standard NDT work procedure
In Reply to Ashish at 14:58 Sep-10-2019 (Opening).

Ash,
The general idea is that you write your own version to your own requirements.
These two documents are the same, line for line, so it is not necessary to have both documents.

The text in these two documents is very useful to copy, but be certain that you read carefully what you are saying (example in several places it says "When required by the written practice.....". here you should decide if it is a requirement or not, and if it is a requirement, say so, but if not, do not mention it)

If you do not use a certain level of operator (e.g. Level 1 Limited), then you do not have to include this level in your document (exception is Level 3. You must define L3 requirements)
The training and experience hours shown in the document are mandatory minimum amounts. You can decide to use more, but you may not decide to use less.

Another useful document is Nadcap checklist AC7114 section 5.

Hope that helps.

Godfrey

 
 Reply 
 
Rafid O. Lopez
, NDT Level 3
Mexico, Joined Jan 2010, 87

Rafid O. Lopez

, NDT Level 3
Mexico,
Joined Jan 2010
87
18:34 Sep-17-2019
Re: NAS 410 Aviation Standard NDT work procedure
In Reply to Ashish at 14:58 Sep-10-2019 (Opening).

Ashis

My recomendation is, use an EN4179 Level 3 for this purpose; some times the company need pay to have this service, a procedure alone is the same as NAS410 Standard alone; what you need is the Level 3 signature.

The standard and the procedure shall be almost the same in content. Remember with EN4179 you will need a RESPONSIBLE LEVEL 3, designated by the employer.

If you have specific questions, the best practice is use an EN4179 Level 3.

 
 Reply 
 

Product Spotlight

Research and Application Development For NDT

Acuren’s Research and Application Development specializes in the development of advanced ultraso
...
nic inspection techniques and systems for challenging inspection applications, with an emphasis on practical solutions which are field deployable. Services include manual and automated ultrasonic inspection system development, inspection technique optimization using laboratory scale studies and ultrasonic modeling (CIVA, BeamTool), preparing technical justification for technique evaluation and qualification (Probability of Detection and sizing accuracy studies), inspection/calibration/analysis procedure preparation to support field deployment of custom techniques, and development of custom imaging algorithms to support challenging inspection applications.
>

FD800 Bench Top Flaw Detectors

The bench-top FD800 flaw detector range combines state-of-the-art flaw detection with advanced mater
...
ial thickness capabilities. Designed for use in the laboratory these gauges are the tool you need for all your flaw detecting needs.
>

TraiNDE UT

TraiNDE UT is a virtual tool associated with a signal database which simulates real inspection con
...
ditions for numerous applications (Type A/V1 block, DAC block, welds and plates).
>

VeeScan AirCraft Wheel Inspection

The VEESCAN offers maximum flexibility, has a proven mechanical design and records of breakdown-fr
...
ee operation of over 365 days. Appealing to companies in the Aerospace industry, the VEESCAN is ideal for all wheel-testing environments. With a wide selection of probes, the VeeScan allows your wheel testing facility the flexibility to select the most compatible configurations with their workload.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window