where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

836 views
Technical Discussions
General
General
02:27 Nov-12-2004
Square vs Round Transducers

Why does AWS D1.1 specify to use a square transducer and does not allow round transducers for doing shear wave inspections. CSA W59, the Canadian equivilent does not stipulate that sqaure transducers have to be used.

Why do AWS specify square?


 
 Reply 
 
Ed Ginzel
R & D, -
Materials Research Institute, Canada, Joined Nov 1998, 1304

Ed Ginzel

R & D, -
Materials Research Institute,
Canada,
Joined Nov 1998
1304
06:05 Nov-13-2004
Re: Square vs Round Transducers
----------- Start Original Message -----------
: Why does AWS D1.1 specify to use a square transducer and does not allow round transducers for doing shear wave inspections. CSA W59, the Canadian equivilent does not stipulate that sqaure transducers have to be used.
: Why do AWS specify square?
------------ End Original Message ------------

I cannot state with authority as to WHY AWS imposes this rule, but perhaps it is just part of the "tradition" of the document being carried forward for nearly 50 years. In a correspondence with a committee member I was told that this was because square or rectangular elements have a "more uniform sound field". This is not true when you plot echo responses off ideal targets such as a FBH. Mechanical clamping in the corners of a rectangular probe is not the same as the clamping along the sides. The effect is that lobes occur. This is often seen on the ends of cylindrically focused immersion probes. The mechanical clamping on a round element is generally of better uniformity thereby providing a more uniform sound field than the square probes.

There are several issues with the old AWS D1 code that make it "different" from all the rest. One in particular is the way they treat amplitude correction with the strange formula for compensation of soundpath (the same rate of compensation is applied for all angles!). Other Codes tend to use a method of DAC compensation that allow for angle variations in echo-transmittance.
But AWS has finally updated itself in the 2004 edition. Annex K allows other options and even describes the more familiar DAC construction. But this is apparently so radical that it requires the approval of the engineer.
Ed


 
 Reply 
 

Product Spotlight

NDT Master Lecturer

In the program both university professors and practitioners will give lectures, which guarantees the
...
oretical depth and practical inside. Academic Director: Prof. Dr. Christian Boller
The following lecturers are not complete: Prof. Tadeusz Stepinski, Prof. Wieslaw Staszewski, Prof. Frank Walther, Prof. Giovanni Bruno, Prof. Gerd Dobmann, Prof. Philippe Guy
>

32:128PR PAUT & 2-ch TOFD Flaw Detector: SyncScan 2

●32:128PR PAUT with optional 2-ch TOFD to maximize your efficiency ●Support PR mode for corrosi
...
on inspection ●Multiple solutions for welds & corrosion ●Faster scan speed (Approximately 3 meters/minute) ●Light weight: 4kg only including battery
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

OPBOX with standard software is able to do all types of inspections and measurements: flaw detection in welds and materials, scanning of objects, testing composite materials, forged and moulded pieces, many UT inspections, measurements of properties of ma

Typical applications: UT measurements with pulse technique, Measurement of thicknesses also at hig
...
h temperatures, Measurements of properties of materials, including fluids and gases We are delivering a standard version of the software (for any Microsoft Windows up to 10 x64 with Microsoft Hardware certification report Approved) and for special needs: SDK with ready to use examples for LabView, MATLAB x64, C++ wrapper for dll, Python and Linux., and also low-level description of how to control our devices directly from any USB tools
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window