where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

WesDyne International (AMDATA Products)
WesDyne is an engineering and technical services firm dedicated to providing standard and custom nondestructive examinations (NDE) products and systems
1455 views
Technical Discussions
David LAVASTRE
Engineering,
EDF CEIDRE, France, Joined Nov 2003, 11

David LAVASTRE

Engineering,
EDF CEIDRE,
France,
Joined Nov 2003
11
02:00 Nov-18-2004
Ultrasonic testing supplier in Europe

Hi everybody,
My company is looking for UT NDT supplier in europe.
The part to be inspected are aircraft engine forged parts in Titanium or Nickel base alloys.
Just for information the maximum diameter is almost 400mm and maximum height is almost 800mm.
The ultrasonic testing must be made in total immersion technique and must be approved by our quality organisation before production (Qualification following our procedure).

Can you help me ?

David
NDT UT Level 3 / SNECMA Moteurs
Gennevilliers plant - France


 
 Reply 
 
Franco Baratta
Franco Baratta
01:27 Nov-19-2004
Re: Ultrasonic testing supplier in Europe
----------- Start Original Message -----------
: Hi everybody,
: My company is looking for UT NDT supplier in europe.
: The part to be inspected are aircraft engine forged parts in Titanium or Nickel base alloys.
: Just for information the maximum diameter is almost 400mm and maximum height is almost 800mm.
: The ultrasonic testing must be made in total immersion technique and must be approved by our quality organisation before production (Qualification following our procedure).
: Can you help me ?
: David
: NDT UT Level 3 / SNECMA Moteurs
: Gennevilliers plant - France
------------ End Original Message ------------

Dear Mr.Lavastre,

Bytest is a service NDT agency sited in Via Pisa 12- 10088 Volpiano (TO) - Italy.

We are already involved in UT of steel forgings for aeronautic sector, in compliance with SAE AMS STD 2154, and could be in the position of satisfy your request. Please transmit your testing and qualification procedures to allow us checking our position against your requirements.

Best Regards

Franco Baratta
Technical Director
UT Lev.3 EN 473


 
 Reply 
 
Godfrey Hands
Consultant,
PRI Nadcap, United Kingdom, Joined Nov 1998, 306

Godfrey Hands

Consultant,
PRI Nadcap,
United Kingdom,
Joined Nov 1998
306
02:54 Nov-22-2004
Re: Ultrasonic testing supplier in Europe
Dear David,
NDT Consultants Ltd. in Coventry, United Kingdom are able to help you with this testing application.

We have a large immersion ultrasonic tank.
We have ultrasonic capability from 1MHz up to 80 MHz
We are an accredited training establishment for Aerospace applications, and our level 3's and Level 2's are certified to NAS 410 and EN 4179.

Can you please contact me directly and we can discuss how we can be of service to SNECMA in this application (and possibly others also)

With my best Regards

Godfrey Hands
Phone +44 2476 511 151

----------- Start Original Message -----------
: Hi everybody,
: My company is looking for UT NDT supplier in europe.
: The part to be inspected are aircraft engine forged parts in Titanium or Nickel base alloys.
: Just for information the maximum diameter is almost 400mm and maximum height is almost 800mm.
: The ultrasonic testing must be made in total immersion technique and must be approved by our quality organisation before production (Qualification following our procedure).
: Can you help me ?
: David
: NDT UT Level 3 / SNECMA Moteurs
: Gennevilliers plant - France
------------ End Original Message ------------




 
 Reply 
 
Shashikant Gawand.
Shashikant Gawand.
04:28 Nov-24-2004
Re: Ultrasonic testing supplier in Europe
----------- Start Original Message -----------
: Hi everybody,
: My company is looking for UT NDT supplier in europe.
: The part to be inspected are aircraft engine forged parts in Titanium or Nickel base alloys.
: Just for information the maximum diameter is almost 400mm and maximum height is almost 800mm.
: The ultrasonic testing must be made in total immersion technique and must be approved by our quality organisation before production (Qualification following our procedure).
: Can you help me ?
: David
: NDT UT Level 3 / SNECMA Moteurs
: Gennevilliers plant - France
------------ End Original Message ------------

Dear Sir

Enrico Enterprises is India based company can provide "One stop NDT at one roof"

We have involved to many Immerssion type project.

Please forward us the basic inspection procedure and your requirment. We will provide the Right Inspection service in very much Cost effective.

Waiting for your reply.

Thanking you and warm regardes.

Shashikant Gawand
Tech. Division
Mobile:- 09821764682





 
 Reply 
 
Michel Macé
Michel Macé
06:12 Dec-12-2004
Re: Ultrasonic testing supplier in Europe
----------- Start Original Message -----------
: Hi everybody,
: My company is looking for UT NDT supplier in europe.
: The part to be inspected are aircraft engine forged parts in Titanium or Nickel base alloys.
: Just for information the maximum diameter is almost 400mm and maximum height is almost 800mm.
: The ultrasonic testing must be made in total immersion technique and must be approved by our quality organisation before production (Qualification following our procedure).
: Can you help me ?
: David
: NDT UT Level 3 / SNECMA Moteurs
: Gennevilliers plant - France
------------ End Original Message ------------

Hi
We have 6 tanks for this application (UT and or ET immersion)and are qualified by Snecma and GE
We have also ASEA part 145 and FAR 145 approval

And we are close to you...
2 plants :
78 Montesson France tel 33139527000
26 Bourg de Péage France tel 33475707373



 
 Reply 
 
S.V.Swamy
Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex , India, Joined Feb 2001, 787

S.V.Swamy

Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex ,
India,
Joined Feb 2001
787
07:29 Dec-14-2004
Re: Ultrasonic testing supplier in Europe
----------- Start Original Message -----------
: : Hi everybody,
: : My company is looking for UT NDT supplier in europe.
: : The part to be inspected are aircraft engine forged parts in Titanium or Nickel base alloys.
: : Just for information the maximum diameter is almost 400mm and maximum height is almost 800mm.
: : The ultrasonic testing must be made in total immersion technique and must be approved by our quality organisation before production (Qualification following our procedure).
: : Can you help me ?
: : David
: : NDT UT Level 3 / SNECMA Moteurs
: : Gennevilliers plant - France
: Hi
: We have 6 tanks for this application (UT and or ET immersion)and are qualified by Snecma and GE
: We have also ASEA part 145 and FAR 145 approval
: And we are close to you...
: 2 plants :
: 78 Montesson France tel 33139527000
: 26 Bourg de P�age France tel 33475707373
------------ End Original Message ------------
Dear Michel,

ET by immersion? I feel there isa mistake (in what you wrote or even more probable in my understanding).

Swamy



 
 Reply 
 
MACE Michel
MACE Michel
01:36 Dec-14-2004
Re: Ultrasonic testing supplier in Europe
----------- Start Original Message -----------
: : : Hi everybody,
: : : My company is looking for UT NDT supplier in europe.
: : : The part to be inspected are aircraft engine forged parts in Titanium or Nickel base alloys.
: : : Just for information the maximum diameter is almost 400mm and maximum height is almost 800mm.
: : : The ultrasonic testing must be made in total immersion technique and must be approved by our quality organisation before production (Qualification following our procedure).
: : : Can you help me ?
: : : David
: : : NDT UT Level 3 / SNECMA Moteurs
: : : Gennevilliers plant - France
: : Hi
: : We have 6 tanks for this application (UT and or ET immersion)and are qualified by Snecma and GE
: : We have also ASEA part 145 and FAR 145 approval
: : And we are close to you...
: : 2 plants :
: : 78 Montesson France tel 33139527000
: : 26 Bourg de P�age France tel 33475707373
: Dear Michel,
: ET by immersion? I feel there is a mistake (in what you wrote or even more probable in my understanding).
: Swamy
------------ End Original Message ------------

Hi Swamy

We can do ET inspection in the water, without difficulties, we do not to drain the tank...

Aslo we can inspect some parts in same time with UT and ET

Michel



 
 Reply 
 

Product Spotlight

VeeScan AirCraft Wheel Inspection

The VEESCAN offers maximum flexibility, has a proven mechanical design and records of breakdown-fr
...
ee operation of over 365 days. Appealing to companies in the Aerospace industry, the VEESCAN is ideal for all wheel-testing environments. With a wide selection of probes, the VeeScan allows your wheel testing facility the flexibility to select the most compatible configurations with their workload.
>

MUSE Mobile Ultrasonic Equipment

The MUSE, a portable ultrasonic imaging system, was developed for in-field inspections of light-weig
...
ht structures. The MUSE consists of a motor-driven manipulator, a water circulation system for the acoustic coupling and a portable ultrasonic flaw detector (USPC 3010). The MUSE provides images of internal defects (A-, B-,C- and D-scan).
>

NDT Master Lecturer

In the program both university professors and practitioners will give lectures, which guarantees the
...
oretical depth and practical inside. Academic Director: Prof. Dr. Christian Boller
The following lecturers are not complete: Prof. Tadeusz Stepinski, Prof. Wieslaw Staszewski, Prof. Frank Walther, Prof. Giovanni Bruno, Prof. Gerd Dobmann, Prof. Philippe Guy
>

Cygnus 6+ PRO Multi-Mode Ultrasonic Thickness Gauge

The Cygnus 6+ PRO thickness gauge is the most advance gauge within the Cygnus range with key featu
...
res including: comprehensive data logging; A-scan and B-scan display; manual gain control; Bluetooth connectivity; and much more. With its unique dual display and three measuring modes (Multiple-Echo, Echo-Echo and Single-Echo), this surface thickness gauge offers maximum versatility for inspections.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window