where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
242 views
Technical Discussions
A. VAlente
A. VAlente
18:06 Mar-19-2020
move inspection setup's to diferents omniscan MX2

We have different omniscan MX2 machine and with different version of software in our laboratory.
When I make a setup calibration and do inspection for a specific job on some time... I w'like have the option to save the setup and can use it in to other omniscan MX2 machine for the same type of job.
But when copy setup to other machine card it did not work/run...

Tanks for attention
AV

 
 Reply 
 
Nick Bublitz
Other, Phased Array Analysist
VeriPhase, USA, Joined May 2010, 132

Nick Bublitz

Other, Phased Array Analysist
VeriPhase,
USA,
Joined May 2010
132
18:48 Mar-19-2020
Re: move inspection setup's to diferents omniscan MX2
In Reply to A. VAlente at 18:06 Mar-19-2020 (Opening).

Valente,

You will probably need to provide more info:
1. What did not work, was there an error message, could the file not be opened on the other machine etc.
2. What software versions, it is likely if the software versions are different and especially if significantly far apart , a setup on one would not work on another.

You may be able to do the following:
1. Find the newest version of all units
2. Get a second card and copy this card
3. Update all units to this version
4. When you need to run the old version, put that card in
5. When you need to run the new setups, use the card copy, the unit will be upgraded to allow this

or, if you don't have a need to stay on the old software, just update all units software and the setups should work

1
 
 Reply 
 
Levi Porter
R & D,
Dacon Inspection Technologies, Thailand, Joined Jan 2017, 55

Levi Porter

R & D,
Dacon Inspection Technologies,
Thailand,
Joined Jan 2017
55
11:17 Mar-22-2020
Re: move inspection setup's to diferents omniscan MX2
In Reply to A. VAlente at 18:06 Mar-19-2020 (Opening).

Hi A. VAlente,
In addition to other requirements you should know this will only be possible if both units have the same P/R module.

1
 
 Reply 
 
Liliana Silva
Engineering,
ISQ, Portugal, Joined Feb 2009, 2

Liliana Silva

Engineering,
ISQ,
Portugal,
Joined Feb 2009
2
15:36 Mar-23-2020
Re: move inspection setup's to diferents omniscan MX2
In Reply to A. VAlente at 18:06 Mar-19-2020 (Opening).

Valente,
Esqueceu-se de dizer que o problema não é da versão do software mas sim do módulo de Phased Array, são equipamentos de gerações diferentes.....

 
 Reply 
 

Product Spotlight

GUL QSR1® Scanning

How do you measure pipe wall thickness without direct access to the area? QSR® Scanning - Guide Wav
...
e Quantitative Short Range Scanning.
>

YXLON Cougar EVO

Scalable small footprint X-ray inspection systems for assembly and laboratory applications. The
...
YXLON Cougar EVO series was designed to provide the "best-in- class" inspection solutions for SMT, semiconductor, and laboratory assembly applications, while maintaining a small system footprint for maximum convenience. With optimized software and hardware, these systems produce higher quality and more consistent results than other electronics inspection systems currently on the market.
>

IntraPhase Athena Phased Array System

The Athena Phased Array system, manufactured by WesDyne NDE Products & Technology, consists of a pha
...
sed array acquisition system and PC running IntraSpect software. A PC is used to perform acquisition, analysis and storage of the data. System hardware is capable of operating up to four data sets with any combination of phased array or conventional UT probes. NOW AVAILABLE IN 64-64 CONFIGURATION.
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window