where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

248 views
Technical Discussions
John
,
Ireland, Joined Mar 2020, 4

John

,
Ireland,
Joined Mar 2020
4
20:19 Mar-23-2020
ASME RAD Ref. Code Penetreted Thickness.

With regards ASME V article 2, estimated penetrated thickness (WT+excess metal), shall not exceed the maximum stated by the referencing code.

Could anyone advise which sections of ASME B31.3, VII and IX, that this information can be found.

 
 Reply 
 
Diego
Consultant,
Freelance, Spain, Joined May 2013, 197

Diego

Consultant,
Freelance,
Spain,
Joined May 2013
197
12:26 Mar-25-2020
Re: ASME RAD Ref. Code Penetreted Thickness.
In Reply to John at 20:19 Mar-23-2020 (Opening).

Hi John.

If your question is related to T-276.2 (a), in ASME V:

 -See the definitions for nominal thickness and weld
   reinforcement, in the applicable codes.

 -RT is not required in ASME VII.

 -For ASME B31.3. See the symbols "L" and "F" in the
tables 341.3.2 and K341.3.2, respectively.

 -For ASME IX. RT may be used for welder qualification or
  welding operator and, for these qualifications, the weld
  reinforcement is not considered; therefore this value
will be 0

 
 Reply 
 
John
John
14:04 Mar-25-2020
Re: ASME RAD Ref. Code Penetreted Thickness.
In Reply to Diego at 12:26 Mar-25-2020 .

Thanks for the information Diego.

I made a mistake, I meant VIII (section 8), not VII.

 
 Reply 
 
Diego
Consultant,
Freelance, Spain, Joined May 2013, 197

Diego

Consultant,
Freelance,
Spain,
Joined May 2013
197
14:37 Mar-25-2020
Re: ASME RAD Ref. Code Penetreted Thickness.
In Reply to John at 14:04 Mar-25-2020 .

If you use ASME VIII Div 1, you should consider UW-35 in general; but you should keep in mind that UW-35 may be modified by another paragraph of this division (as an example: see UHT 84)

 
 Reply 
 

Product Spotlight

NEW Wheel Type Phased Array Probe

DOPPLER NEW Wheel Type Phased Array Probe, more stable, new tyre makes lesser acoustic attenuation
...
, much lighter makes easier to handle, more slim size, magnetic and mechanical encoder optional etc...more
>

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

Robotic laser shearography enables 100% inspection of complex, flight-critical composite structures

An article in “Composites World Magazine” showcases Non Destructive Testing of aero-structures
...
with Laser Shearography. Over the years Dantec Dynamics has supplied many solutions for the aerospace industry. Referring to specific customer projects several of these cases are examined to outline the advantages of using Laser Shearography for automated defect detection.
>

TraiNDE UT

TraiNDE UT is a virtual tool associated with a signal database which simulates real inspection con
...
ditions for numerous applications (Type A/V1 block, DAC block, welds and plates).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window