where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

939 views
Technical Discussions
Derek
Derek
07:16 Nov-05-2004
Surface Probe Eddy Current Inspection of Tubing

Has anyone here ever used a surface eddy current probe to examine stainless steel tubing? Specifically small diamter tubing (<= 1/8"). If anyone has any insight or links to information related to this they could offer I would appreciate it. Please send an email to: ddlucero@lanl.gov.


 
 Reply 
 
dirk wagner
NDT Inspector
ec-works, Germany, Joined Dec 2004, 2

dirk wagner

NDT Inspector
ec-works,
Germany,
Joined Dec 2004
2
01:29 Dec-09-2004
Re: Surface Probe Eddy Current Inspection of Tubing
----------- Start Original Message -----------
: Has anyone here ever used a surface eddy current probe to examine stainless steel tubing? Specifically small diamter tubing (<= 1/8"). If anyone has any insight or links to information related to this they could offer I would appreciate it. Please send an email to: ddlucero@lanl.gov.
------------ End Original Message ------------

Hi,
i did testing of stainless steel in german nuclear power plants. We were searching (successfully) for inside defects with eddy-current probes from the boundary of the tube.
More relevant than the diameter is the wall-thickness.
I hope, I can help you


 
 Reply 
 
S.V.Swamy
Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex , India, Joined Feb 2001, 787

S.V.Swamy

Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex ,
India,
Joined Feb 2001
787
04:21 Dec-12-2004
Re: Surface Probe Eddy Current Inspection of Tubing
----------- Start Original Message -----------
: : Has anyone here ever used a surface eddy current probe to examine stainless steel tubing? Specifically small diamter tubing (<= 1/8"). If anyone has any insight or links to information related to this they could offer I would appreciate it. Please send an email to: ddlucero@lanl.gov.
: Hi,
: i did testing of stainless steel in german nuclear power plants. We were searching (successfully) for inside defects with eddy-current probes from the boundary of the tube.
: More relevant than the diameter is the wall-thickness.
: I hope, I can help you
------------ End Original Message ------------
Hi,

SS tubes (austenitic) are normally tested during manufacture using an encircling coil from OD and during in-service inspection using an ID Bobbin coil. I would like to know the type of defects that you are trying to detect with the surface probe.

Swamy


 
 Reply 
 

Product Spotlight

VOGT Ultrasonics awarded innovation champion

Let go of the old and try something new. VOGT convinced the jury in the 27th round of the TOP 100
...
innovation competition. Our team is very pleased to officially belong to the TOP 100 in Germany!
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

FD800 Bench Top Flaw Detectors

The bench-top FD800 flaw detector range combines state-of-the-art flaw detection with advanced mater
...
ial thickness capabilities. Designed for use in the laboratory these gauges are the tool you need for all your flaw detecting needs.
>

PAUT Probes

Typical Phased Array probes have frequencies between 1MHz and 20MHz and the number of wafers is 10
...
to 128. M2 Electronics offers customers conventionally ultrasound probes and the ability to provide high-precision Phased Array Ultrasound Probes of up to 256 wafers. We can also customize the probe for our customers to meet the specific application requirements of the user.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window