where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

305 views
Career Discussions
John
,
Ireland, Joined Mar 2020, 4

John

,
Ireland,
Joined Mar 2020
4
20:10 Mar-23-2020
Degree program

Having L2 qualifications in RT,UT,PT and weld inspection, I am wondering would it be worth my while completing a degree in mechanical engineering?

Would it be a waste of time? Would I be better off investing the time and money in other NDT areas?

I'm looking at future options such as plant inspection or asset integrity management.

Any feedback would be greatly appreciated.

 
 Reply 
 
Michel Couture
NDT Inspector,
consultant, Canada, Joined Sep 2006, 891

Michel Couture

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
891
18:05 Apr-13-2020
Re: Degree program
In Reply to John at 20:10 Mar-23-2020 (Opening).

John,

No one can anwser that question for you. It depends on what you want to do with the rest of you life. You are in charge of your destiny.

 
 Reply 
 
laurie
Australia, Joined Feb 2019, 39

laurie

Australia,
Joined Feb 2019
39
00:08 Apr-14-2020
Re: Degree program
In Reply to John at 20:10 Mar-23-2020 (Opening).

I've got a mechanical engineering degree and L3 in MT, PT, UT, RT and L2 in ET.
A mechanical engineering degree is a broad program covering electronics, electrical, structural, hydraulics, welding, programming, materials, dynamics, etc, and helps in many areas but there are probably better choices for NDT and Inspection.
If you want to focus on NDT then it'd be better to get a degree in NDT.
If you want to focus on plant inspection then it's a lot less than 4 years of study to get API qualifications.

 
 Reply 
 
John
,
Ireland, Joined Mar 2020, 4

John

,
Ireland,
Joined Mar 2020
4
11:21 Apr-14-2020
Re: Degree program
In Reply to laurie at 00:08 Apr-14-2020 .

Laurie,

Thank you for the information. At the moment I am just weighing up options of concentrating on either NDT, plant inspection or new build weld inspection / QC.

Looking at your qualifications, you seem to have a lot of knowledge in these areas.

I would like to boost my CV and knowledge with a third level qualification or else API's. Thanks again for the feedback, I was finding it difficult to get solid career advice.

 
 Reply 
 

Product Spotlight

High-performance Linear Phased Array Probes

Available to order from stock in a range of 5MHz – 7.5MHz and from 16 to 64 elements. Designed w
...
ith piezo-composite elements, Phoenix phased array probes provide high-resolution imaging to maximise sensitivity; accurate ultrasonic detection and sizing of defects in welds; and effective corrosion mapping. Housed in a rugged stainless steel case for on-site industrial NDT applications.
>

FAAST-PA! OEM Patented phased Array for high speed UT inspection

Multiangle, Multifocus, Multifrequency, Multibeam. Instead of stacking UT electronics and having m
...
any PA probes, FAAST-PA is able to transmit all delay laws within ONE single shot in Real time.
>

Conformable wedge transducer

The conformability is obtained with a flexible membrane filled with water between the transducer and
...
the inspected component. The coupling between the membrane and the component requires a small quantity of water or couplant. The conformable wedge combines the acoustic performance of immersion technique with good coupling and low attenuation.
>

32:128PR PAUT & 2-ch TOFD Flaw Detector: SyncScan 2

●32:128PR PAUT with optional 2-ch TOFD to maximize your efficiency ●Support PR mode for corrosi
...
on inspection ●Multiple solutions for welds & corrosion ●Faster scan speed (Approximately 3 meters/minute) ●Light weight: 4kg only including battery
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window