where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1377 views
Technical Discussions
David LAVASTRE
Engineering,
EDF CEIDRE, France, Joined Nov 2003, 11

David LAVASTRE

Engineering,
EDF CEIDRE,
France,
Joined Nov 2003
11
02:00 Nov-18-2004
Ultrasonic testing supplier in Europe

Hi everybody,
My company is looking for UT NDT supplier in europe.
The part to be inspected are aircraft engine forged parts in Titanium or Nickel base alloys.
Just for information the maximum diameter is almost 400mm and maximum height is almost 800mm.
The ultrasonic testing must be made in total immersion technique and must be approved by our quality organisation before production (Qualification following our procedure).

Can you help me ?

David
NDT UT Level 3 / SNECMA Moteurs
Gennevilliers plant - France


    
 
 Reply 
 
Franco Baratta
Franco Baratta
01:27 Nov-19-2004
Re: Ultrasonic testing supplier in Europe
----------- Start Original Message -----------
: Hi everybody,
: My company is looking for UT NDT supplier in europe.
: The part to be inspected are aircraft engine forged parts in Titanium or Nickel base alloys.
: Just for information the maximum diameter is almost 400mm and maximum height is almost 800mm.
: The ultrasonic testing must be made in total immersion technique and must be approved by our quality organisation before production (Qualification following our procedure).
: Can you help me ?
: David
: NDT UT Level 3 / SNECMA Moteurs
: Gennevilliers plant - France
------------ End Original Message ------------

Dear Mr.Lavastre,

Bytest is a service NDT agency sited in Via Pisa 12- 10088 Volpiano (TO) - Italy.

We are already involved in UT of steel forgings for aeronautic sector, in compliance with SAE AMS STD 2154, and could be in the position of satisfy your request. Please transmit your testing and qualification procedures to allow us checking our position against your requirements.

Best Regards

Franco Baratta
Technical Director
UT Lev.3 EN 473


    
 
 Reply 
 
Godfrey Hands
Consultant,
PRI Nadcap, United Kingdom, Joined Nov 1998, 302

Godfrey Hands

Consultant,
PRI Nadcap,
United Kingdom,
Joined Nov 1998
302
02:54 Nov-22-2004
Re: Ultrasonic testing supplier in Europe
Dear David,
NDT Consultants Ltd. in Coventry, United Kingdom are able to help you with this testing application.

We have a large immersion ultrasonic tank.
We have ultrasonic capability from 1MHz up to 80 MHz
We are an accredited training establishment for Aerospace applications, and our level 3's and Level 2's are certified to NAS 410 and EN 4179.

Can you please contact me directly and we can discuss how we can be of service to SNECMA in this application (and possibly others also)

With my best Regards

Godfrey Hands
Phone +44 2476 511 151

----------- Start Original Message -----------
: Hi everybody,
: My company is looking for UT NDT supplier in europe.
: The part to be inspected are aircraft engine forged parts in Titanium or Nickel base alloys.
: Just for information the maximum diameter is almost 400mm and maximum height is almost 800mm.
: The ultrasonic testing must be made in total immersion technique and must be approved by our quality organisation before production (Qualification following our procedure).
: Can you help me ?
: David
: NDT UT Level 3 / SNECMA Moteurs
: Gennevilliers plant - France
------------ End Original Message ------------




    
 
 Reply 
 
Shashikant Gawand.
Shashikant Gawand.
04:28 Nov-24-2004
Re: Ultrasonic testing supplier in Europe
----------- Start Original Message -----------
: Hi everybody,
: My company is looking for UT NDT supplier in europe.
: The part to be inspected are aircraft engine forged parts in Titanium or Nickel base alloys.
: Just for information the maximum diameter is almost 400mm and maximum height is almost 800mm.
: The ultrasonic testing must be made in total immersion technique and must be approved by our quality organisation before production (Qualification following our procedure).
: Can you help me ?
: David
: NDT UT Level 3 / SNECMA Moteurs
: Gennevilliers plant - France
------------ End Original Message ------------

Dear Sir

Enrico Enterprises is India based company can provide "One stop NDT at one roof"

We have involved to many Immerssion type project.

Please forward us the basic inspection procedure and your requirment. We will provide the Right Inspection service in very much Cost effective.

Waiting for your reply.

Thanking you and warm regardes.

Shashikant Gawand
Tech. Division
Mobile:- 09821764682





    
 
 Reply 
 
Michel Macé
Michel Macé
06:12 Dec-12-2004
Re: Ultrasonic testing supplier in Europe
----------- Start Original Message -----------
: Hi everybody,
: My company is looking for UT NDT supplier in europe.
: The part to be inspected are aircraft engine forged parts in Titanium or Nickel base alloys.
: Just for information the maximum diameter is almost 400mm and maximum height is almost 800mm.
: The ultrasonic testing must be made in total immersion technique and must be approved by our quality organisation before production (Qualification following our procedure).
: Can you help me ?
: David
: NDT UT Level 3 / SNECMA Moteurs
: Gennevilliers plant - France
------------ End Original Message ------------

Hi
We have 6 tanks for this application (UT and or ET immersion)and are qualified by Snecma and GE
We have also ASEA part 145 and FAR 145 approval

And we are close to you...
2 plants :
78 Montesson France tel 33139527000
26 Bourg de Péage France tel 33475707373



    
 
 Reply 
 
S.V.Swamy
Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex , India, Joined Feb 2001, 787

S.V.Swamy

Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex ,
India,
Joined Feb 2001
787
07:29 Dec-14-2004
Re: Ultrasonic testing supplier in Europe
----------- Start Original Message -----------
: : Hi everybody,
: : My company is looking for UT NDT supplier in europe.
: : The part to be inspected are aircraft engine forged parts in Titanium or Nickel base alloys.
: : Just for information the maximum diameter is almost 400mm and maximum height is almost 800mm.
: : The ultrasonic testing must be made in total immersion technique and must be approved by our quality organisation before production (Qualification following our procedure).
: : Can you help me ?
: : David
: : NDT UT Level 3 / SNECMA Moteurs
: : Gennevilliers plant - France
: Hi
: We have 6 tanks for this application (UT and or ET immersion)and are qualified by Snecma and GE
: We have also ASEA part 145 and FAR 145 approval
: And we are close to you...
: 2 plants :
: 78 Montesson France tel 33139527000
: 26 Bourg de P�age France tel 33475707373
------------ End Original Message ------------
Dear Michel,

ET by immersion? I feel there isa mistake (in what you wrote or even more probable in my understanding).

Swamy



    
 
 Reply 
 
MACE Michel
MACE Michel
01:36 Dec-14-2004
Re: Ultrasonic testing supplier in Europe
----------- Start Original Message -----------
: : : Hi everybody,
: : : My company is looking for UT NDT supplier in europe.
: : : The part to be inspected are aircraft engine forged parts in Titanium or Nickel base alloys.
: : : Just for information the maximum diameter is almost 400mm and maximum height is almost 800mm.
: : : The ultrasonic testing must be made in total immersion technique and must be approved by our quality organisation before production (Qualification following our procedure).
: : : Can you help me ?
: : : David
: : : NDT UT Level 3 / SNECMA Moteurs
: : : Gennevilliers plant - France
: : Hi
: : We have 6 tanks for this application (UT and or ET immersion)and are qualified by Snecma and GE
: : We have also ASEA part 145 and FAR 145 approval
: : And we are close to you...
: : 2 plants :
: : 78 Montesson France tel 33139527000
: : 26 Bourg de P�age France tel 33475707373
: Dear Michel,
: ET by immersion? I feel there is a mistake (in what you wrote or even more probable in my understanding).
: Swamy
------------ End Original Message ------------

Hi Swamy

We can do ET inspection in the water, without difficulties, we do not to drain the tank...

Aslo we can inspect some parts in same time with UT and ET

Michel



    
 
 Reply 
 

Product Spotlight

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

XRHRobotStar

In high volume industries like automotive the requirement for a hundred percent X-ray inspection c
...
reates a bottleneck in the production. The XRHRobotStar is a fully Automated Defect Recognition (ADR) capable robot-system that allows an ultra-fast in-line inspection.
>

NovaScope 6000

The all-digital Novascope 6000 is a portable, ultra-high precision thickness gauge for high-speed
...
thickness measurement. Novascope 6000 has unmatched capabilities and unique features including: •Superior Resolution with high contrast, high-speed color RF display •High pulser voltage •Real-time video output •Increased internal/external data storage •Programmable SetUp features •Battery & AC Powered
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window