where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
455 views
Technical Discussions
Terry Anson
Terry Anson
01:24 Feb-09-2001
Thanks for the help!

I appreciate all the advice! I have one more question. Is is possible to find a transducer that can sweep frequency? Maybe I should phrase it like this: If I buy a transducer that is rated at 200khz, will it will only send out a 200khz signal? Or will the voltage, current, and frequency of the pulse sent to the transducer determine this?


 
 Reply 
 
Paul Meyer
R & D,
GE Inspection Technologies, USA, Joined Nov 1998, 47

Paul Meyer

R & D,
GE Inspection Technologies,
USA,
Joined Nov 1998
47
04:22 Feb-09-2001
Re: Thanks for the help!
Hi Terry,
Most ultrasound transducers respond to a range of frequencies. If you sweep the frequency of a constant amplitude input signal and monitor the output amplitude of the transducer you will difine the frequency response of the transducer. The bandwidth of the transducer (frequency range of the response) can be increased by changing the internal design of the device, but this sometimes reduces the maximum output amplitude.
Decide the frequency range that you need, and then work with your supplier to get as close to that as you can.
Paul


: I appreciate all the advice! I have one more question. Is is possible to find a transducer that can sweep frequency? Maybe I should phrase it like this: If I buy a transducer that is rated at 200khz, will it will only send out a 200khz signal? Or will the voltage, current, and frequency of the pulse sent to the transducer determine this?
.



 
 Reply 
 
Hanspeter Loertscher
Hanspeter Loertscher
07:58 Feb-09-2001
Re: Thanks for the help!
All transducers have a certain bandwidth, i.e. the frequency is not sharply defined. The larger the bandwidth, the less sensitive the transducer. Resonant transducers, as we use them for air-coupled ultrasound, are highly resonant and have therefore a narrow bandwidth. Our solution to overcome the narrow bandwidth - the frequency of one specific transducer cannot cannot be swept - is an instrument, the SONDA 007CX, which is capable of driving transducers of different nominal frequencies, ranging from 50 kHz to 1 MHz. Each frequency is then precisely tuned to the resonant frequency of the transducer. We are preparing a paper and a presentation, which will show some very estonishing results using different frequencies for material testing.


 
 Reply 
 

Product Spotlight

High-performance Linear Phased Array Probes

Available to order from stock in a range of 5MHz – 7.5MHz and from 16 to 64 elements. Designed w
...
ith piezo-composite elements, Phoenix phased array probes provide high-resolution imaging to maximise sensitivity; accurate ultrasonic detection and sizing of defects in welds; and effective corrosion mapping. Housed in a rugged stainless steel case for on-site industrial NDT applications.
>

A1525 SOLO

A1525 Solo – the most compact and affordable TMF unit with two phased array transducers and 3D v
...
isualization and analysis software in standard delivery set. A compact, ergonomic and easy to handheld Phased Array unit based on Total Focusing Method for easy-going imaging of inspection objects with two-dimensional and three-dimensional visualization and evaluation of inspection results.
>

FD800 Bench Top Flaw Detectors

The bench-top FD800 flaw detector range combines state-of-the-art flaw detection with advanced mater
...
ial thickness capabilities. Designed for use in the laboratory these gauges are the tool you need for all your flaw detecting needs.
>

TESTD-PT SYSTEM

Pulse thermography is a non-contact test method that is ideal for the characterization of thin fil
...
ms and coatings or the detection of defects. With a remarquable short test time and a high detection sensitivity, the Telops TESTD-PT is the perfect tool for non- destructive testing. With such high frame rates, it is even possible to investigate highly conductive or diffusive materials.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window