where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

187 views
Technical Discussions
Masaru Kuwahara
Engineering,
Japan, Joined Jul 2020, 2

Masaru Kuwahara

Engineering,
Japan,
Joined Jul 2020
2
03:34 Jul-10-2020
Selection of RT reference film

Hello.
Which RT reference film shall be used for a steel castings valve, thickness from 25mm to 100 mm?

Case 1: ASTM E446 only
Case 2: E446 for up to 25.8 mm thickness area and E186 over 25.8 mm area.

I think Case 2 is correct, but it is difficult to show up to 25.8 mm area and other area on a film....

Please let me know what do you do at this kind of time?
Thanks in advance.

 
 Reply 
 
Masaru Kuwahara
Engineering,
Japan, Joined Jul 2020, 2

Masaru Kuwahara

Engineering,
Japan,
Joined Jul 2020
2
03:48 Jul-10-2020
Re: Selection of RT reference film
In Reply to Masaru Kuwahara at 03:34 Jul-10-2020 (Opening).

Sorry, mistype....

"I think Case 2 is correct, but it is difficult to show up to 50.8 mm area and other area on a film...."

E446: for up to 2 in.(50.8mm)
E186: 2 - 4 1/2 in.

 
 Reply 
 
Diego
Consultant,
Freelance, Spain, Joined May 2013, 201

Diego

Consultant,
Freelance,
Spain,
Joined May 2013
201
23:08 Jul-10-2020
Re: Selection of RT reference film
In Reply to Masaru Kuwahara at 03:48 Jul-10-2020 .

Hello Masaru.
The answer to your question will depend on the standards, specifications or codes to be applied.
However, as a general idea, ASTM E446 should be used for thicknesses equal to or less than 50 mm, and ASTM E186 for thicknesses greater than 50 mm but less than or equal to 115 mm.
You could use ASTM E446 for both thickness ranges, but this would be very severe for case 1.
You may use a double film technique and a combination of a single and double viewing so as to cover a greater latitude in part thickness with a single exposure.
Regards.

 
 Reply 
 
Diego
Consultant,
Freelance, Spain, Joined May 2013, 201

Diego

Consultant,
Freelance,
Spain,
Joined May 2013
201
23:21 Jul-10-2020
Re: Selection of RT reference film
In Reply to Diego at 23:08 Jul-10-2020 .

Sorry, there is a typo.
Where I say "for case 1", I mean "for thicknesses greater than 50 mm but less than or equal to 115 mm"

 
 Reply 
 

Product Spotlight

NEW Wheel Type Phased Array Probe

DOPPLER NEW Wheel Type Phased Array Probe, more stable, new tyre makes lesser acoustic attenuation
...
, much lighter makes easier to handle, more slim size, magnetic and mechanical encoder optional etc...more
>

HD-CR 35 NDT Computed Radiography System

Portable high-resolution CR scanner for all radiography applications - weld testing, profile images
...
and aerospace. No matter what type of radiographic testing you are performing, the unique TreFoc Technology of the HD-CR 35 NDT imaging plate scanner always guarantees the highest image quality.
>

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

On Demand Webinar: Improve the Efficiency and Accuracy of Inspection Scanning

On-demand webinar on scanning technology that helps improve the efficiency and accuracy of ultrasoni
...
c inspections in oil and gas, aerospace, manufacturing and other industrial applications. The webinar features a scanning solution for multiple inspection environments, including flat and curved specimens, magnetic and nonmagnetic surfaces and raster scanning over long distances. View it today.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window