where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1637 views
Technical Discussions
xiaoyan
Student
University of Florida, USA, Joined Mar 2002, 8

xiaoyan

Student
University of Florida,
USA,
Joined Mar 2002
8
05:23 Feb-18-2005
AE used in the bending testing of concrete beam

I am graduate student. I used Micro-Disp system (8 channels) to monitor the cracking process of concrete beam. I use the biult-in function of AE location function. However, the locations results are so scattered that I can not see any cracking pattern. I want to see if anybody could good experience and like to share with me.

Thank you and have a good weekend!


 
 Reply 
 
Mark Carlos
Engineering, -
MISTRAS Products & Systems, USA, Joined Mar 2002, 4

Mark Carlos

Engineering, -
MISTRAS Products & Systems,
USA,
Joined Mar 2002
4
07:56 Feb-18-2005
Re: AE used in the bending testing of concrete beam
Xiaoyan,

AEwin has excellent location capabilities, and extremely versatile, and for all types of structures. I would be happy to review your files and help if you can send me a layout and DTA file showing an example. My email is mfcarlos@pacndt.com

Regards, Mark Carlos

----------- Start Original Message -----------
: I am graduate student. I used Micro-Disp system (8 channels) to monitor the cracking process of concrete beam. I use the biult-in function of AE location function. However, the locations results are so scattered that I can not see any cracking pattern. I want to see if anybody could good experience and like to share with me.
: Thank you and have a good weekend!
------------ End Original Message ------------




 
 Reply 
 
Simon Amallraja
Simon Amallraja
05:05 Feb-19-2005
Re: AE used in the bending testing of concrete beam
----------- Start Original Message -----------
: Xiaoyan,
: AEwin has excellent location capabilities, and extremely versatile, and for all types of structures. I would be happy to review your files and help if you can send me a layout and DTA file showing an example. My email is mfcarlos@pacndt.com
: Regards, Mark Carlos
: : I am graduate student. I used Micro-Disp system (8 channels) to monitor the cracking process of concrete beam. I use the biult-in function of AE location function. However, the locations results are so scattered that I can not see any cracking pattern. I want to see if anybody could good experience and like to share with me.
: : Thank you and have a good weekend!
------------ End Original Message ------------

You can contact Mr Hermut Vallen or Jens Forker in Vallen SYsteme GmbH. They will help you. e.mail: sales@vallen.de They also have some free s/w for student applications. If found suitable, you need to buy them.

D.Simon Amallraja.


 
 Reply 
 
Allen Green
Allen Green
02:39 Feb-23-2005
Re: AE used in the bending testing of concrete beam
Xiaoyan,
For your information Vallen - Systeme GmbH will let you evaluate their software free of charge on a tme limited basis. They have a conversion program that will read data files from other AE systems and allow their software to perform the analysis. If you are really not able to get the results you need you may want to consider contacting them. (www.vallen.de / support@vallen.de)
They do have a client in the US who is testing concrete beams. Contact me for more information.
Good luck with your project.
Allen Green, Acoustic Technology Group, 916 483-1311.

----------- Start Original Message -----------
: : Xiaoyan,
: : AEwin has excellent location capabilities, and extremely versatile, and for all types of structures. I would be happy to review your files and help if you can send me a layout and DTA file showing an example. My email is mfcarlos@pacndt.com
: : Regards, Mark Carlos
: : : I am graduate student. I used Micro-Disp system (8 channels) to monitor the cracking process of concrete beam. I use the biult-in function of AE location function. However, the locations results are so scattered that I can not see any cracking pattern. I want to see if anybody could good experience and like to share with me.
: : : Thank you and have a good weekend!
: You can contact Mr Hermut Vallen or Jens Forker in Vallen SYsteme GmbH. They will help you. e.mail: sales@vallen.de They also have some free s/w for student applications. If found suitable, you need to buy them.
: D.Simon Amallraja.
------------ End Original Message ------------




 
 Reply 
 
Athanasios Anastasopoulos
Director,
Mistras Group, Greece, Joined Jan 2000, 14

Athanasios Anastasopoulos

Director,
Mistras Group,
Greece,
Joined Jan 2000
14
02:41 Feb-25-2005
Re: AE used in the bending testing of concrete beam
Dear Xiaoyan

Different reasons might contribute to the scatter of your located events. Since you do not mentione the dimensions of your specimens and the location method used I cannot comment on the reasons contributing to the scatter. The type of concrete might be the deciding parameter as well. Also note the scattered locations might represent real or secondary events (freting, microcracks, etc). Once location is set up properly, density plots of AE-WINN will certainly help you to highlight the dominant crack.

Reffering to ourexperience please note we have also performed bending experiments of concrete beams. The beams were 2.6meters long with cross section of 150mmX300mm (Two row of 3 embeded steel reinforcemets on top and bottom - compresive and tensile side respectivelly of the cross section. We used 14 PAC-R15I sensors and PAC DiSP 24ch. Sensors were distributed at both sides of the cross section. As location method we used the 3D location of AE-WIN and experimented with the advanced location settings such as Min/Max hits per events, event definition timing etc. Validation of location experimentation was based on HSU sources and after a few trials worked fine.
We performed tests on beams with and without external FRP reinforcment. The speciemns and reinforcements were designed to drive specific failure modes (shear/tensile etc). Using this set up we were able to distignusish the type of failure (shear or tensile crack) at early stage from the located events.
Should you need further info on this set-up or other trials (location based on features/timming extracted from waveforms, moment tensor, etc) please contact me directly through e-mail or call me.
With Best Regards
Nassos Anastasopoulos

----------- Start Original Message -----------
: Xiaoyan,
: For your information Vallen - Systeme GmbH will let you evaluate their software free of charge on a tme limited basis. They have a conversion program that will read data files from other AE systems and allow their software to perform the analysis. If you are really not able to get the results you need you may want to consider contacting them. (www.vallen.de / support@vallen.de)
: They do have a client in the US who is testing concrete beams. Contact me for more information.
: Good luck with your project.
: Allen Green, Acoustic Technology Group, 916 483-1311.
: : : Xiaoyan,
: : : AEwin has excellent location capabilities, and extremely versatile, and for all types of structures. I would be happy to review your files and help if you can send me a layout and DTA file showing an example. My email is mfcarlos@pacndt.com
: : : Regards, Mark Carlos
: : : : I am graduate student. I used Micro-Disp system (8 channels) to monitor the cracking process of concrete beam. I use the biult-in function of AE location function. However, the locations results are so scattered that I can not see any cracking pattern. I want to see if anybody could good experience and like to share with me.
: : : : Thank you and have a good weekend!
: : You can contact Mr Hermut Vallen or Jens Forker in Vallen SYsteme GmbH. They will help you. e.mail: sales@vallen.de They also have some free s/w for student applications. If found suitable, you need to buy them.
: : D.Simon Amallraja.
------------ End Original Message ------------




 
 Reply 
 
xiaoyan
Student
University of Florida, USA, Joined Mar 2002, 8

xiaoyan

Student
University of Florida,
USA,
Joined Mar 2002
8
07:42 Mar-08-2005
thank all who helped with me, Especially PAC

with all the help, I realize the AEwin has a strong capacity in acquiring and analyzing the AE data. However, all the help I get make it possible that I get to know how to apply them. so, here I would like to thank you for all the help I got and I would like give my special appreciation to PAC company for their patient guidance!



 
 Reply 
 

Product Spotlight

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window