where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

YXLON International GmbH
459 views
Technical Discussions
S. Kazemi
S. Kazemi
09:31 May-31-2005
ultrasonic set up

Dear friends
I plan to prepare a ultrasonic set up for laboratory testing of Wood based materials.So I need a shematic diagram of the set up with detail.thanks for your attention in advance.


    
 
 Reply 
 
Neil Burleigh
Sales
Krautkramer Australia Pty Ltd, Australia, Joined Dec 2002, 157

Neil Burleigh

Sales
Krautkramer Australia Pty Ltd,
Australia,
Joined Dec 2002
157
01:48 Jun-01-2005
Re: ultrasonic set up
----------- Start Original Message -----------
: Dear friends
: I plan to prepare a ultrasonic set up for laboratory testing of Wood based materials.So I need a shematic diagram of the set up with detail.thanks for your attention in advance.
------------ End Original Message ------------


Dear Kazemi,
Before you prepare your ultrasonic setup have you determined what you are trying to detect in the wood based materials? Sound velocity changes, voids or imperfections, delamination of bonding, rotting or decay.
What mode of sound propagation will you be using?
What type of samples will you be testing?
At a later date will this setup be transferred into the industry for field use?

Incidently once you have clarified these points you will be halfway to planning your own ultrasonic set up.

Regards

Neil Burleigh




    
 
 Reply 
 
Manfred R Richter
Manfred R Richter
02:55 Jun-01-2005
Re: ultrasonic set up
Dear Kazemi,
you may have same info in the address http://www.ipef.br/publicacoes/scientia/nr63/cap20.pdf, and also with the following University people that have some experience with:
fabiana@sc.usp.br and mcarreir@sc.usp.br.
Hope this help.
Regards,
Manfred


----------- Start Original Message -----------
: Dear friends
: I plan to prepare a ultrasonic set up for laboratory testing of Wood based materials.So I need a shematic diagram of the set up with detail.thanks for your attention in advance.
------------ End Original Message ------------




    
 
 Reply 
 
Jim Knowles
Jim Knowles
03:17 Jun-01-2005
Re: ultrasonic set up
Dear Kazemi
In order to plan your ultrasonic evaluation equipment, surely you need to know what the wood density, water content, surface feature and the equipment and method or technique you intend to use. Evaluate your needs, what is required of the test and the type and presentation of the data before the schematic.

: : Dear friends
: : I plan to prepare a ultrasonic set up for laboratory testing of Wood based materials.So I need a shematic diagram of the set up with detail.thanks for your attention in advance.
:
: Dear Kazemi,
: Before you prepare your ultrasonic setup have you determined what you are trying to detect in the wood based materials? Sound velocity changes, voids or imperfections, delamination of bonding, rotting or decay.
: What mode of sound propagation will you be using?
: What type of samples will you be testing?
: At a later date will this setup be transferred into the industry for field use?
: Incidently once you have clarified these points you will be halfway to planning your own ultrasonic set up.
: Regards
: Neil Burleigh
------------ End Original Message ------------




    
 
 Reply 
 
Johan
Johan
00:51 Jun-03-2005
Re: ultrasonic set up
Dear Kazemi
It's difficult to give you a straight answer, which the other writers allready mentioned.

The frequencies used are normally from 1 MHz for thin samples and down to 50 kHz for very thick samples.
The most common set-up is to use pulsed transmission method due the high attenuation (could be 400dB/m). The frequency choice is also depending in which direction your sending you sound, wood has different velocity and attenuation in different direction.
If it's the material properties you are interested in you need transducers for both longitudinal and shear waves.
Then inspection wood the normally is to measure the transit time.
A conventional UT equipment for steel could work down to around 0.25-1.0 MHz depending on freq.filter, but output voltage is low 200-300V.
Equipment suited for concrete is more useful, 24-1000 kHz, output voltage is 250-1200V.
You need
a pulser, to generate the sound wave
a timer, to measure the transit time
pulser and timer is usually one part.
two transducers, a pair, for each frequency
You may need an oscilloscope if you would like to study the puls shape and amplitude.

Best Regards
Johan
----------- Start Original Message -----------
: Dear friends
: I plan to prepare a ultrasonic set up for laboratory testing of Wood based materials.So I need a shematic diagram of the set up with detail.thanks for your attention in advance.
------------ End Original Message ------------




    
 
 Reply 
 

Product Spotlight

Lyft™: Pulsed Eddy Current Reinvented

PEC Reinvented—CUI Programs Redefined Corrosion under insulation (CUI) is possibly the greatest u
...
nresolved asset integrity problem in the industry. Current methods for measuring wall thickness with liftoff, without removing insulation, all have severe limitations. Eddyfi introduces Lyft — a reinvented, high-performance pulsed eddy current (PEC) solution. The patent- pending system features a state-of-the-art portable instrument, real- time C-scan imaging, fast data acquisition with grid-mapping and dynamic scanning modes, and flexibility with long cables. It can also scan through thick metal and insulation, as well as aluminum, stainless steel, and galvanized steel weather jackets. Who else but Eddyfi to reinvent an eddy current technique and redefine CUI programs. Got Lyft?
>

Navic - Steerable Modular Automated Scanner

The Navic is a modular, motorized, steerable scanner designed to carry multiple attachments used
...
in various scanning and inspection applications. The Navic is capable of weld scanning (girth welds and long seam welds), automated corrosion mapping, and tank scanning.
>

Research and Applications Development For NDT

The Research and Applications Development (RAD) group is a newly formed team within Acuren dedicat
...
ed to tackling challenging inspection problems. Our focus is the development of novel, field deployable, advanced inspection techniques for use in cases where standard NDT methods are ineffective. We don't wait for new innovations, we engineer them. From concept to commissioning.
>

Echomac® Small

Available with up to eight channels of electronics to detect and evaluate thickness, flaws and eccen
...
tricity, this UT tester is housed in a convenient, smaller cabinet. This instrument can be used in conjunction with bubbler or immersion tank systems, or with a test bench or in laboratory applications. The Echomac® Small is available in the FD4, FD6 or FD6A versions.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window