where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

ZETEC, Inc.
Zetec is a global leader in nondestructive testing (NDT) solutions for the critical inspection needs of industries the world counts on every day, ...
458 views
Technical Discussions
S. Kazemi
S. Kazemi
09:31 May-31-2005
ultrasonic set up

Dear friends
I plan to prepare a ultrasonic set up for laboratory testing of Wood based materials.So I need a shematic diagram of the set up with detail.thanks for your attention in advance.


    
 
 Reply 
 
Neil Burleigh
Sales
Krautkramer Australia Pty Ltd, Australia, Joined Dec 2002, 157

Neil Burleigh

Sales
Krautkramer Australia Pty Ltd,
Australia,
Joined Dec 2002
157
01:48 Jun-01-2005
Re: ultrasonic set up
----------- Start Original Message -----------
: Dear friends
: I plan to prepare a ultrasonic set up for laboratory testing of Wood based materials.So I need a shematic diagram of the set up with detail.thanks for your attention in advance.
------------ End Original Message ------------


Dear Kazemi,
Before you prepare your ultrasonic setup have you determined what you are trying to detect in the wood based materials? Sound velocity changes, voids or imperfections, delamination of bonding, rotting or decay.
What mode of sound propagation will you be using?
What type of samples will you be testing?
At a later date will this setup be transferred into the industry for field use?

Incidently once you have clarified these points you will be halfway to planning your own ultrasonic set up.

Regards

Neil Burleigh




    
 
 Reply 
 
Manfred R Richter
Manfred R Richter
02:55 Jun-01-2005
Re: ultrasonic set up
Dear Kazemi,
you may have same info in the address http://www.ipef.br/publicacoes/scientia/nr63/cap20.pdf, and also with the following University people that have some experience with:
fabiana@sc.usp.br and mcarreir@sc.usp.br.
Hope this help.
Regards,
Manfred


----------- Start Original Message -----------
: Dear friends
: I plan to prepare a ultrasonic set up for laboratory testing of Wood based materials.So I need a shematic diagram of the set up with detail.thanks for your attention in advance.
------------ End Original Message ------------




    
 
 Reply 
 
Jim Knowles
Jim Knowles
03:17 Jun-01-2005
Re: ultrasonic set up
Dear Kazemi
In order to plan your ultrasonic evaluation equipment, surely you need to know what the wood density, water content, surface feature and the equipment and method or technique you intend to use. Evaluate your needs, what is required of the test and the type and presentation of the data before the schematic.

: : Dear friends
: : I plan to prepare a ultrasonic set up for laboratory testing of Wood based materials.So I need a shematic diagram of the set up with detail.thanks for your attention in advance.
:
: Dear Kazemi,
: Before you prepare your ultrasonic setup have you determined what you are trying to detect in the wood based materials? Sound velocity changes, voids or imperfections, delamination of bonding, rotting or decay.
: What mode of sound propagation will you be using?
: What type of samples will you be testing?
: At a later date will this setup be transferred into the industry for field use?
: Incidently once you have clarified these points you will be halfway to planning your own ultrasonic set up.
: Regards
: Neil Burleigh
------------ End Original Message ------------




    
 
 Reply 
 
Johan
Johan
00:51 Jun-03-2005
Re: ultrasonic set up
Dear Kazemi
It's difficult to give you a straight answer, which the other writers allready mentioned.

The frequencies used are normally from 1 MHz for thin samples and down to 50 kHz for very thick samples.
The most common set-up is to use pulsed transmission method due the high attenuation (could be 400dB/m). The frequency choice is also depending in which direction your sending you sound, wood has different velocity and attenuation in different direction.
If it's the material properties you are interested in you need transducers for both longitudinal and shear waves.
Then inspection wood the normally is to measure the transit time.
A conventional UT equipment for steel could work down to around 0.25-1.0 MHz depending on freq.filter, but output voltage is low 200-300V.
Equipment suited for concrete is more useful, 24-1000 kHz, output voltage is 250-1200V.
You need
a pulser, to generate the sound wave
a timer, to measure the transit time
pulser and timer is usually one part.
two transducers, a pair, for each frequency
You may need an oscilloscope if you would like to study the puls shape and amplitude.

Best Regards
Johan
----------- Start Original Message -----------
: Dear friends
: I plan to prepare a ultrasonic set up for laboratory testing of Wood based materials.So I need a shematic diagram of the set up with detail.thanks for your attention in advance.
------------ End Original Message ------------




    
 
 Reply 
 

Product Spotlight

FAAST-PA! OEM Patented phased Array for high speed UT inspection

Multiangle, Multifocus, Multifrequency, Multibeam. Instead of stacking UT electronics and having m
...
any PA probes, FAAST-PA is able to transmit all delay laws within ONE single shot in Real time.
>

Compact NDT inspection-heads for measurements with active thermography

The compact inspection head is suitable for thermographic ndt tasks. The uncooled infrared camera
...
is specially developed for NDI-tasks and offers a thermal sensitivity until now known only from thermal imagers with cooled detector. All required components and functions are integrated into the inspection-head. You will only need an ethernet cable to connect the sensor with the evaluation system.
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

Panther

M2M PANTHER is a phased-array equipment designed for both desktop and industrial applications, offer
...
ing unparalleled performance in a compact unit. It combines the speed required for industrial integrated Phased-Array Ultrasound (PAUT) solutions, with the most complete set of total focusing method (TFM) imaging techniques, making it the ultimate tool for R&D and procedure qualification.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window