where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
359 views
Technical Discussions
Adeel
Student
KAIST, South Korea, Joined Jun 2005, 4

Adeel

Student
KAIST,
South Korea,
Joined Jun 2005
4
05:53 Jun-09-2005
Lamb Waves

Hi Everybody
I want to perform experiment for the "Damage detection in concrete structures using Lamb Waves". So any body can tell me that Are Lamb waves can be used to detect damages in thick materials cos i have read that they are mainly used for thin plates.
Also what experimental setup i need to build to perform my experiment on it.
Thanx and Regards


 
 Reply 
 
Ed T.
Ed T.
09:10 Jun-10-2005
Re: Lamb Waves
----------- Start Original Message -----------
: Hi Everybody
: I want to perform experiment for the "Damage detection in concrete structures using Lamb Waves". So any body can tell me that Are Lamb waves can be used to detect damages in thick materials cos i have read that they are mainly used for thin plates.
: Also what experimental setup i need to build to perform my experiment on it.
: Thanx and Regards
------------ End Original Message ------------

Lamb wave or plate wave propagation is normally generated between two parallel surfaces of a test object. For an object to sufficiently support Lamb Waves or plate waves, it must be thin enough to allow penetration of a surface wave to the opposite surface.
I don't believe Lamb waves would be able to exist in concrete. The OD and ID surfaces must be parrallel and the material must be extremely thin to generate Lamb Waves. You may want to look at low frequency longitudinal waves.




 
 Reply 
 
Adeel
Student
KAIST, South Korea, Joined Jun 2005, 4

Adeel

Student
KAIST,
South Korea,
Joined Jun 2005
4
01:26 Jun-11-2005
Re: Lamb Waves
----------- Start Original Message -----------
: : Hi Everybody
: : I want to perform experiment for the "Damage detection in concrete structures using Lamb Waves". So any body can tell me that Are Lamb waves can be used to detect damages in thick materials cos i have read that they are mainly used for thin plates.
: : Also what experimental setup i need to build to perform my experiment on it.
: : Thanx and Regards
: Lamb wave or plate wave propagation is normally generated between two parallel surfaces of a test object. For an object to sufficiently support Lamb Waves or plate waves, it must be thin enough to allow penetration of a surface wave to the opposite surface.
: I don't believe Lamb waves would be able to exist in concrete. The OD and ID surfaces must be parrallel and the material must be extremely thin to generate Lamb Waves. You may want to look at low frequency longitudinal waves.
------------ End Original Message ------------

Hi ED T
Thanx for ur reply. The reason i asked you that whether Lamb Waves can be used for damage detection in concrete is that i read one paper in which this Lamb wave was used to detect damage in Concrete structure. The specimen used had cross section of 300 X 200mm and was 300mm thick. Do you think with such dimensions Lamb Wave can be generated and damage can be detected.
If u want i can send you that paper as well.
Thanx


 
 Reply 
 

Product Spotlight

Lyft™: Pulsed Eddy Current Reinvented

PEC Reinvented—CUI Programs Redefined Corrosion under insulation (CUI) is possibly the greatest u
...
nresolved asset integrity problem in the industry. Current methods for measuring wall thickness with liftoff, without removing insulation, all have severe limitations. Eddyfi introduces Lyft — a reinvented, high-performance pulsed eddy current (PEC) solution. The patent- pending system features a state-of-the-art portable instrument, real- time C-scan imaging, fast data acquisition with grid-mapping and dynamic scanning modes, and flexibility with long cables. It can also scan through thick metal and insulation, as well as aluminum, stainless steel, and galvanized steel weather jackets. Who else but Eddyfi to reinvent an eddy current technique and redefine CUI programs. Got Lyft?
>

NEOS III

NEOS III is Logos Imagings lightest DR system. With a built-in battery and internal wireless commu
...
nication, the NEOS III is perfect for users that want to quickly assess an item.
>

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

NDTkit RT

NDTkit RT, TESTIA's Digital Radiography software The NDTkit product line software for X-ray analysi
...
s. NDTkit RT is a software benefiting from the Ultis kernel which is dedicated to radiographic image analysis. It offers a set of tools and filtering processes to assist RT operators in finding relevant flaws.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window