where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

ZETEC, Inc.
Zetec is a global leader in nondestructive testing (NDT) solutions for the critical inspection needs of industries the world counts on every day, ...
2091 views
Technical Discussions
Johnnie
Johnnie
02:22 Jul-10-2005
Ultrasonic angle beam formula for cylindrical forgings.

I would like to know the formula for proper angle use to impinge id of thick wallcylindrical forgings/pipe.


 
 Reply 
 
Ed T.
Ed T.
05:25 Jul-13-2005
Re: Ultrasonic angle beam formula for cylindrical forgings.
----------- Start Original Message -----------
: I would like to know the formula for proper angle use to impinge id of thick wallcylindrical forgings/pipe.
------------ End Original Message ------------

SinØ 1 = (ID/OD) * SinØ2
SINØ2 being the desired angle on the ID surface.


 
 Reply 
 
K.V. Rasmussen
K.V. Rasmussen
09:15 Jul-13-2005
Re: Ultrasonic angle beam formula for cylindrical forgings.
----------- Start Original Message -----------
: I would like to know the formula for proper angle use to impinge id of thick wallcylindrical forgings/pipe.
------------ End Original Message ------------

Many years ago I found some useful formulas in Materials Evaluation No. 43, November 1985, page 1489.
This was published under the heading 'NDT Solutions' by Jim Johnson.

If you are interested contact me directly via e-mail and I can send you a PDF copy.





 
 Reply 
 
N.DHANASEKARAN
R & D
WELDING RESEARCH INSTITUTE, BHEL, India, Joined Jun 2005, 3

N.DHANASEKARAN

R & D
WELDING RESEARCH INSTITUTE, BHEL,
India,
Joined Jun 2005
3
01:42 Jul-15-2005
Re: Ultrasonic angle beam formula for cylindrical forgings.


Hello!
Well known formula to calculate the penetrated depth (d) by angle beam (¥è), knowing outer radius(r) of the pipe is given below:

d = r (1- sin¥è)

By substituting the thickness of the pipe in place of "d", for full penetration by the sound beam, one can calculate the angle required.
For example , 25 mm thick pipe of radius 100 mm will require 45 degree angle probe to detect inner notch in the ref.pipe.
N.DHANASEKARAN


-


---------- Start Original Message -----------
: : I would like to know the formula for proper angle use to impinge id of thick wallcylindrical forgings/pipe.
: Sin¨ª 1 = (ID/OD) * Sin¨ª2
: SIN¨ª2 being the desired angle on the ID surface.
: Sorry misprint.
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

New PHAsis module for longitudinal weld seam inspection

PHAsis® Phased Array manual ultrasonic spot weld inspection device is now ideally suited for test
...
ing of longitudinally welded seams (e.g. Arplas® seam, short line seams) with a length of 3 to 12 mm.
>

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

Ultrasonic Testing Immersion Tanks with Unmatched Scanning Features

TecScan’s non-destructive testing Ultrasonic Immersion Tanks & scanners are designed for high pe
...
rformance and demanding NDT testing applications. Our Scan3D™ line of High Precision Immersion Tanks are specifically designed for automated ultrasonic testing of complex composites parts used in aerospace and industrial applications.
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window