where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

LECOEUR ELECTRONIQUE
The Specialist of electronics for ultrasonic testing
440 views
Technical Discussions
KRISHNAN
KRISHNAN
07:52 Jul-14-2005
WAVE PATTERN

Dear Sirs,
Is it same of wave pattern (wavelenth and other characteristics) which produced in transducer element and RECEIVING signal after interfering with material' grain structures.

Because I feel that wave length will be distrubed when it crosses too many size of grain boundries.

Please kindly explain me about this topic.

Thank you very much

Regards,

Krishnan


 
 Reply 
 
Dr. Anish Kumar
R & D, Scientist
Indira Gandhi Centre for Atomic Research, India, Joined Mar 2000, 7

Dr. Anish Kumar

R & D, Scientist
Indira Gandhi Centre for Atomic Research,
India,
Joined Mar 2000
7
07:49 Jul-16-2005
Re: WAVE PATTERN
Hi Krishnan, You are right. The frequency characteristics of the ultrasoic wave (I assume you are talking about ultrasoic wave only) changes as it propagates through materials with different grain sizes due to different frequency dependent attenuation. You may see our following papers:

1.Anish Kumar, T. Jayakumar and Baldev Raj "Ultrasonic Spectral Analysis for Microstructural Characterization in Austenitic and Ferritic Steels", Philosophical Magazine A, Vol. 80 (2000) pp. 2469-2487.
2.Anish Kumar, T. Jayakumar, P. Palanichamy and Baldev Raj, "Influence of Grain Size on Ultrasonic Spectral Parameters in AISI Type 316 Stainless Steel
Scripta Materialia, Vol. 40 (1999) pp. 333-340.

Regards,
Anish

----------- Start Original Message -----------
: Dear Sirs,
: Is it same of wave pattern (wavelenth and other characteristics) which produced in transducer element and RECEIVING signal after interfering with material' grain structures.
: Because I feel that wave length will be distrubed whenit crosses too many size of grain boundries.
: Please kindly explain me about this topic.
: Thank you very much
: Regards,
: Krishnan
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

A1525 SOLO

A1525 Solo – the most compact and affordable TMF unit with two phased array transducers and 3D v
...
isualization and analysis software in standard delivery set. A compact, ergonomic and easy to handheld Phased Array unit based on Total Focusing Method for easy-going imaging of inspection objects with two-dimensional and three-dimensional visualization and evaluation of inspection results.
>

GUL Subsea Solutions - Screeening & Monitoring

To inspect new and existing subsea lines, you need proven technology and experience. GUL offers it's
...
technology to solve this challenge: GUL Subsea and gMAT Transducer Rings.
>

Robotic laser shearography enables 100% inspection of complex, flight-critical composite structures

An article in “Composites World Magazine” showcases Non Destructive Testing of aero-structures
...
with Laser Shearography. Over the years Dantec Dynamics has supplied many solutions for the aerospace industry. Referring to specific customer projects several of these cases are examined to outline the advantages of using Laser Shearography for automated defect detection.
>

Echomac® PA Bar Tester

The Echomac® PA BT provides 100% inspection of round bars for core and surface defects, at speeds u
...
p to 2 m/sec, depending on the specific application. The unit allows producers to handle a much larger range of diameters in one installation, and is available in 3 models to test 10 – 75mm diameter (small model); 20 – 130mm (medium model) or 50 – 254mm (large model) bars.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window