where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
615 views
Technical Discussions
Jennifer Lavallee
Jennifer Lavallee
04:02 Jun-15-1999
Re:Absorbed Dose of Radionuclides

Hello,
I am a summer student at Babcock & Wilcox Canada.
I am doing some research regarding some radionuclides. I have
the activity levels of three series radionuclides; Thorium 232,
Uranium 235, and Uranium 238. I would like to figure out how to
convert these radionuclides into their aborbed doses. The elements
inside the Thorium 232 series and the activity levels are:
Radionuclide Activity (Bq/kg)
Thallium 208 59
Lead 212 174
Bismuth 212 100
Actinium 228 155
The elments inside the Uranium 235 series are:
Radium 223 93
Thorium 227 48
The elements inside the Uranium 238 series are:
Thorium 234 666
Radium 223 1628
Lead 214 888
Bismuth 214 851

If anyone could help me find the absorbed dosage of any
of these radioisotopes I would greatly appreciate the
assistance.

Sincerely,
Jennifer


 
 Reply 
 
Michael Trinidad
Consultant,
LMATS Pty Ltd , Australia, Joined Jan 2003, 138

Michael Trinidad

Consultant,
LMATS Pty Ltd ,
Australia,
Joined Jan 2003
138
03:39 Jun-16-1999
Re:Absorbed Dose of Radionuclides



 
 Reply 
 
Michael Trinidad
Consultant,
LMATS Pty Ltd , Australia, Joined Jan 2003, 138

Michael Trinidad

Consultant,
LMATS Pty Ltd ,
Australia,
Joined Jan 2003
138
04:58 Jun-16-1999
Re:Absorbed Dose of Radionuclides
Further the previous formulae I did some more digging. The absorbed dose is difficult to calculate as you have to individually calculate the different forms of radiation’s (ie Gamma. Beta, Alpha and Neutron) as each has it’s own weighting factors then additional factors are used for different parts of the body. For instance Alpha particles are significantly reduced by paper and skin but if the dose is internally, for example if ingested the factor is larger.

The factors are detailed in the International Commission on Radiological Protection, Recommendations of International Commission of Radiological Protection, ICRP Publication 26 (Annals of ICRP, Vol 1 No 3) Pergammon Press, Oxford 1977


Michael Trinidad
ETRS NDT Project Supervisor
KBJV Worsley Expansion Project
Direct Tel: 61-8-9781-6232
Fax: 61-8-9781-6233
Email: etrs@kbjv.com

Mike Malaxos
Radiation Safety Services
Direct Tel: 61-8-94750099



 
 Reply 
 

Product Spotlight

PROlineTOP Plug & Play Ultrasonic inspection device

As Plug & Play solution it units all control and operation elements in a small housing and therefo
...
re replaces the typical control cabinet...
>

IntraPhase Athena Phased Array System

The Athena Phased Array system, manufactured by WesDyne NDE Products & Technology, consists of a pha
...
sed array acquisition system and PC running IntraSpect software. A PC is used to perform acquisition, analysis and storage of the data. System hardware is capable of operating up to four data sets with any combination of phased array or conventional UT probes. NOW AVAILABLE IN 64-64 CONFIGURATION.
>

Silverwing RMS PA - Phased-array corrosion mapping

Eddyfi Technologies integrated two market leading solutions, Silverwing’s RMS and M2M’s instru
...
ments to provide a high-speed, remote access ultrasonic phased-array inspection system with live total focusing method (TFM).
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window