where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Teletest
Teletest Focus+ was the first system to use long-range guided wave ultrasonic testing to detect corrosion in pipelines.
867 views
Technical Discussions
prakash
prakash
04:59 Jan-21-2006
NDT of fastner head

can the head of a fastner be tested for crack after forging using some NDT method? If so how?


 
 Reply 
 
P V SASTRY
P V SASTRY
00:15 Jan-22-2006
Re: NDT of fastner head
----------- Start Original Message -----------
: can the head of a fastner be tested for crack after forging using some NDT method? If so how?
------------ End Original Message ------------
They can be very easily tested for the presence of cracks/bursts using wet fluorescent magnetic particle testing(WFMPT),assuming that the fasteners are of ferromagnetic material. This is a fast and reliable method that will detect cracks of even a few microns width when properly applied. Alternately Dye Penetrant testing(PT) also can be used as a stop gap arrangement before you can procure the preffered WFMPT set up.In case the fastners are of non ferromagnetic materials like SS, PT (colour/fluorescent)can only be aplied.



 
 Reply 
 
S.V.Swamy
Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex , India, Joined Feb 2001, 787

S.V.Swamy

Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex ,
India,
Joined Feb 2001
787
06:05 Jan-23-2006
Re: NDT of fastner head
----------- Start Original Message -----------
: can the head of a fastner be tested for crack after forging using some NDT method? If so how?
------------ End Original Message ------------

Dear Prakash,

Yes, there are several options. Magnetic Particle Testing is one (I am assuming that the fastener is magnetic). If you need real time high speed testing, you should think of automated UT and or RT. If you can accept batch testing mode, MT and PT (if non-magnetic material is invoved) may be good enough.

Swamy

Swamy



 
 Reply 
 

Product Spotlight

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Research Center IDEKO develops an ultrasonic train wheel inspection system for CAF

The Basque Research centre IK4-IDEKO has developed a state-of-the-art ultrasonic inspection system f
...
or the train wheel. This system secures a sound condition of train wheels and is thus a significant contribution to rail transport safety. The device was delivered to CAF recently and its use allows the manufacturer to become an approved supplier of rolling stock in Italy, as it meets the demanding homologation standards of this country. \\\\r\\\\n
>

NEOS III

NEOS III is Logos Imagings lightest DR system. With a built-in battery and internal wireless commu
...
nication, the NEOS III is perfect for users that want to quickly assess an item.
>

IntraPhase Athena Phased Array System

The Athena Phased Array system, manufactured by WesDyne NDE Products & Technology, consists of a pha
...
sed array acquisition system and PC running IntraSpect software. A PC is used to perform acquisition, analysis and storage of the data. System hardware is capable of operating up to four data sets with any combination of phased array or conventional UT probes. NOW AVAILABLE IN 64-64 CONFIGURATION.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window