where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
497 views
Technical Discussions
Louis
Louis
03:58 Apr-08-2006
Depth reading

Hi everyone,

Here is my probleme,

I have a plate of 1.5 in. At 0,750in I have a hole of 0,062in.
With my USN58L I can know the distance from my transducer, the sound path and the depth of this 0.062in hole.

But, when I move my transducer to Leg 2 with this same hole I still get the good distance from my transducer and also the good sound path, but the depth reading is 3.18in instead of 0,750in. I use a 45 deg. angle transducer and the thickness of the plate on my machine is set at 1.750in.

Is it possible that my machine can't give me the depth after Leg 1 and that I always have to use formulas.

Thanks a lot,

LouisB



 
 Reply 
 
Ed
Ed
06:25 Apr-09-2006
Re: Depth reading
----------- Start Original Message -----------
: Hi everyone,
: Here is my probleme,
: I have a plate of 1.5 in. At 0,750in I have a hole of 0,062in.
: With my USN58L I can know the distance from my transducer, the sound path and the depth of this 0.062in hole.
: But, when I move my transducer to Leg 2 with this same hole I still get the good distance from my transducer and also the good sound path, but the depth reading is 3.18in instead of 0,750in. I use a 45 deg. angle transducer and the thickness of the plate on my machine is set at 1.750in.
: Is it possible that my machine can't give me the depth after Leg 1 and that I always have to use formulas.
: Thanks a lot,
: LouisB
------------ End Original Message ------------

I don't believe the machine is incapable of calculating it. Try setting the thickness of the block at 1.5" as you stated it was and not 1.75". You may also want to check the actual angle in the material. Last but not least make sure you have the correct velocity entered in the machine. Then lastest but not leastest, make sure you are looking at the correct reflector and not an inclusion in the block. Did you try to plot the hole on the second leg?



 
 Reply 
 
Nigel
Engineering, - Specialist services
United Kingdom, Joined Oct 2000, 1096

Nigel

Engineering, - Specialist services
United Kingdom,
Joined Oct 2000
1096
08:20 Apr-09-2006
Re: Depth reading
Louis

3.18" is the beam path skip distance to the hole (1.5 + 0.75)/cos 45 and you say that you get this distance as the "good sound path" which should be just that - 3.18". The fact that your machine is giving this figure as the depth of the hole cannot be mere coincidence, thus somehow the machine must have been set to give the beam path distance as the depth (maybe through a gate).

For a new and expensive piece of kit the sales rep or tech services of the supplier should assist in untangling your problem.

Good luck

Nigel

----------- Start Original Message -----------
: Hi everyone,
: Here is my probleme,
: I have a plate of 1.5 in. At 0,750in I have a hole of 0,062in.
: With my USN58L I can know the distance from my transducer, the sound path and the depth of this 0.062in hole.
: But, when I move my transducer to Leg 2 with this same hole I still get the good distance from my transducer and also the good sound path, but the depth reading is 3.18in instead of 0,750in. I use a 45 deg. angle transducer and the thickness of the plate on my machine is set at 1.750in.
: Is it possible that my machine can't give me the depth after Leg 1 and that I always have to use formulas.
: Thanks a lot,
: LouisB
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

Conformable wedge transducer

The conformability is obtained with a flexible membrane filled with water between the transducer and
...
the inspected component. The coupling between the membrane and the component requires a small quantity of water or couplant. The conformable wedge combines the acoustic performance of immersion technique with good coupling and low attenuation.
>

Ultrasonic Probe Recharacterization Service

NDT Systems offers a comprehensive Aftercare and Recharacterization Service for all our ultrasonic
...
probes. The Recharacterization Service is fully compliant with International ASTM E1065 Standard Guide (and other applicable standards) and offers complete documentation, traceable to the ASTM E1065 Standard. For more details or to schedule Recharacterization Services contact ndtsales@ndtsystems.com
>

Semi-Automated Phased Array Immersion System for Small Composite Parts

Turn-key semi-automated system as an improved and affordable solution for inspection of small comp
...
osite parts. Includes support table, immersion tank, scanner, PA instrument, PC, Analysis software, database, wedge management and other options.
>

High-performance Linear Phased Array Probes

Available to order from stock in a range of 5MHz – 7.5MHz and from 16 to 64 elements. Designed w
...
ith piezo-composite elements, Phoenix phased array probes provide high-resolution imaging to maximise sensitivity; accurate ultrasonic detection and sizing of defects in welds; and effective corrosion mapping. Housed in a rugged stainless steel case for on-site industrial NDT applications.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window