where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1738 views
Technical Discussions
Elmar van den Elzen
Engineering,
Lismar Engineering B.V., Netherlands, Joined Aug 2000, 15

Elmar van den Elzen

Engineering,
Lismar Engineering B.V.,
Netherlands,
Joined Aug 2000
15
01:06 Apr-11-2006
measuring conductivity and permeability

Dear all,

We want to measure the electrical conductivity and the effective magnetic permeability of ferromagnatic samples. The samples typically have a flat site a few cm across. Does anyone know a lab that could do these measurements or know a straight forward method we can set-up ourselves?

Best regards


 
 Reply 
 
Linas Svilainis
R & D,
Kaunas University of Technology, Lithuania, Joined Nov 1998, 68

Linas Svilainis

R & D,
Kaunas University of Technology,
Lithuania,
Joined Nov 1998
68
02:25 Apr-11-2006
Re: measuring conductivity and permeability
Dear Elmar,

you wrote
----------- Start Original Message -----------
: ..We want to measure the electrical conductivity and the effective magnetic permeability of ferromagnatic samples...

Maybe it's a complex permeability you want to measure?
If yes:

.. Does anyone know a lab that could do these measurements or know a straight forward method we can set-up ourselves?...

Then RLC meter with some mathematics on geometry will do. We have prepared the paper on toroidal samples complex permeability measurement in low frequency range (0.1-10MHz). If interested, I can send you some excerpts.

People do complex permeability measurement at GHz. For instance, refer to:
Jacquart. Influence of the electrical resistivity of a ferromagnetic thin film on its permeability measurement performed with a permeameter. Elsevier Journal of Magnetism and Magnetic Materials 281 (2004) 82–91

Best regards

Linas


 
 Reply 
 
Changqing Lee
Changqing Lee
03:37 Apr-11-2006
Re: measuring conductivity and permeability
I have seen people use alternative current potential drop (ACPD) method for measuring the electrical conductivity and the effective magnetic permeability of ferromagnatic samples at the frequency range of several hundred Hz to 10KHz. Please google it yourself.

Eddy current testing is another option. But to determine conductivity and permeability at the same time is always hard.

----------- Start Original Message -----------
: Dear Elmar,
: you wrote
: : ..We want to measure the electrical conductivity and the effective magnetic permeability of ferromagnatic samples...
: Maybe it's a complex permeability you want to measure?
: If yes:
: .. Does anyone know a lab that could do these measurements or know a straight forward method we can set-up ourselves?...
: Then RLC meter with some mathematics on geometry will do. We have prepared the paper on toroidal samples complex permeability measurement in low frequency range (0.1-10MHz). If interested, I can send you some excerpts.
: People do complex permeability measurement at GHz. For instance, refer to:
: Jacquart. Influence of the electrical resistivity of a ferromagnetic thin film on its permeability measurement performed with a permeameter. Elsevier Journal of Magnetism and Magnetic Materials 281 (2004) 82–91
: Best regards
: Linas
------------ End Original Message ------------




 
 Reply 
 
Jim Yukes
Consultant
Canada, Joined Aug 2005, 11

Jim Yukes

Consultant
Canada,
Joined Aug 2005
11
08:15 Apr-13-2006
Re: measuring conductivity and permeability
I checked with a Queens U Magnetics Department Grad & he suggested: There are many different ways to measure permeability depending on the material and application. For some standard methods visit www.astm.org and search for standards with key words "magnetic permeability".

For the conductivity measurement, Google search phrase "contact resistance tester".

----------- Start Original Message -----------
: Dear all,
: We want to measure the electrical conductivity and the effective magnetic permeability of ferromagnatic samples. The samples typically have a flat site a few cm across. Does anyone know a lab that could do these measurements or know a straight forward method we can set-up ourselves?
: Best regards
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

IRIS 9000Plus - Introducing the next generation of heat exchanger inspection.

Representing the seventh generation of the IRIS system, the IRIS 9000 Plus has nearly 200 years of c
...
ombined field inspection experience incorporated in its design. This experience combined with a strong commitment to quality and a history of innovation has made Iris Inspection Services® the undisputed leader in IRIS technology.
>

VeeScan AirCraft Wheel Inspection

The VEESCAN offers maximum flexibility, has a proven mechanical design and records of breakdown-fr
...
ee operation of over 365 days. Appealing to companies in the Aerospace industry, the VEESCAN is ideal for all wheel-testing environments. With a wide selection of probes, the VeeScan allows your wheel testing facility the flexibility to select the most compatible configurations with their workload.
>

NDT.net launches mobile-friendly design

NDT.net has revamped its website providing a mobile-friendly design.The front page received a comp
...
letely new design and all other sections are now reacting responsively on mobile devices. This has been a major step to make our website more user- friendly.
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window