where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Waygate Technologies
Waygate Technologies, a Baker Hughes business (formerly GE Inspection Technologies), is an industrial inspection solutions company and the world ...
491 views
Technical Discussions
Paul Moore
Paul Moore
04:45 Apr-11-2006
Water in Pipe-in-Pipe

I was recently asked if I knew of a method to determine if any water was present in the outer cylinder of a sub-sea pipe-in-pipe flowline. My answer was no. Hence my post.

I realize that it is a very broad question, and there likely is no practical answer.

Considerations:

The inner pipe is fully flooded.
Between the inner and outer pipe there are insulation material, waterstops and centralizers (i.e. no internal access).
Consider the area of concern (between the inner and outer pipe) as not fully flooded.

A measurement of the water that may be present is not required. Just a confirmation that there is water present or not.

Any thoughts or comments (or solutions!) would be greatly appreciated.

Thanks,

Paul




 
 Reply 
 
Ed Ginzel
R & D, -
Materials Research Institute, Canada, Joined Nov 1998, 1300

Ed Ginzel

R & D, -
Materials Research Institute,
Canada,
Joined Nov 1998
1300
04:01 Apr-12-2006
Re: Water in Pipe-in-Pipe
Paul:
I have worked on several projects where water content of pipe was required assessed or where detection of an object within a pipe filled with water was required.

If the outer surface of the pipe is suitable to use a UT probe there may be a hope of SOME form of assessment if the pipe is in the horizontal plane, i.e. the water has collected at the bottom of the outer pipe in the annulus gap. If the gap is filled with water then it can be used to transmit sound across the annulus and you could monitor for the inner pipe indication (lots of gain and sufficient range is required).
But this assumes that the lining insulation is lossy enough that it does not transmit the sound too and get confused with water (although this would be localised and water found over a more general region). Hopefully the insulation will displace the water and not mix as that too could cause some interpretation problems.

----------- Start Original Message -----------
: I was recently asked if I knew of a method to determine if any water was present in the outer cylinder of a sub-sea pipe-in-pipe flowline. My answer was no. Hence my post.
: I realize that it is a very broad question, and there likely is no practical answer.
: Considerations:
: The inner pipe is fully flooded.
: Between the inner and outer pipe there are insulation material, waterstops and centralizers (i.e. no internal access).
: Consider the area of concern (between the inner and outer pipe) as not fully flooded.
: A measurement of the water that may be present is not required. Just a confirmation that there is water present or not.
: Any thoughts or comments (or solutions!) would be greatly appreciated.
: Thanks,
: Paul
:
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

CIVA 2020 UT Module

CIVA NDE Simulation Software is the world leader of NDT Simulation. The UT simulation Module incl
...
udes: - "Beam computation": Beam propagation simulation - "Inspection Simulation": Beam interaction with flaws or specimens The user can simulate a whole inspection process (pulse echo, tandem or TOFD) with a wide range of probes (conventional, Phased- arrays or EMAT), components, and flaws.
>

SITEX CPSERIES

Teledyne ICM’s CPSERIES has been designed with a view to revolutionizing the handling and perfor
...
mances of portable X-Ray sets. Despite having managed to halve the weight of similar portable X-Ray generators available on the market (while continuing to provide the same power output), the SITEX CPSERIES generators feature a shutter, a laser pointer, a beryllium window, an aluminum filter and two integrated diaphragms (customized sizes are available upon request). Without compromising the robustness and reliability for which ICM products are renowned, the small size and light weight of the SITEX CPSERIES will radically change the way that you perform your RT inspections. And you will see a positive impact in terms of both quality and return on investment (ROI).
>

Ultrasonic Squirter/Gantry System

TecScan’s NDT Ultrasonic Gantry Systems are industrial Squirter scanners designed for non-destru
...
ctive quality testing and raster scanning of large structures and parts. The Gantry Systems are usually composed of an Industrial Mechanical Scanner and a Control Room with System Workstation.
>

Ultrasonic Testing Immersion Tanks with Unmatched Scanning Features

TecScan’s non-destructive testing Ultrasonic Immersion Tanks & scanners are designed for high pe
...
rformance and demanding NDT testing applications. Our Scan3D™ line of High Precision Immersion Tanks are specifically designed for automated ultrasonic testing of complex composites parts used in aerospace and industrial applications.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window