where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1321 views
Technical Discussions
Ranjeet singh
Ranjeet singh
05:48 May-24-2006
Differance between Ferrite magnetic permeability

I would like to know expert views about the differance between magnetic permeability and ferrite measurment.
Are they same ?

thanks


 
 Reply 
 
Linas Svilanis
R & D,
Kaunas University of Technology, Lithuania, Joined Nov 1998, 68

Linas Svilanis

R & D,
Kaunas University of Technology,
Lithuania,
Joined Nov 1998
68
01:32 May-26-2006
Re: Differance between Ferrite magnetic permeability
----------- Start Original Message -----------
: I would like to know expert views about the differance between magnetic permeability and ferrite measurment.
: Are they same ?
: thanks
------------ End Original Message ------------

Magnetic permeability is the parameter related to magnetic properties of the material.
Ferrite is the material.
You are asking to compare apples and melons.

Most probably you are concerned about magnetic permeability of ferrite compared to other materials.
Yes, ferrite u will be the highes. But also will exhibit the highes hysteresis. That is, u will be nonlinear function of field strength.
u is usually measured as complex value (see complex permeability), to take all the material electromagnetic interaction into account


 
 Reply 
 
John Brunk
Engineering, NDT Level III
Self employed, part-time, USA, Joined Oct 1999, 162

John Brunk

Engineering, NDT Level III
Self employed, part-time,
USA,
Joined Oct 1999
162
02:53 May-30-2006
Re: Differance between Ferrite magnetic permeability
----------- Start Original Message -----------
: : I would like to know expert views about the differance between magnetic permeability and ferrite measurment.
: : Are they same ?
: : thanks
: Magnetic permeability is the parameter related to magnetic properties of the material.
: Ferrite is the material.
: You are asking to compare apples and melons.
: Most probably you are concerned about magnetic permeability of ferrite compared to other materials.
: Yes, ferrite u will be the highes. But also will exhibit the highes hysteresis. That is, u will be nonlinear function of field strength.
: u is usually measured as complex value (see complex permeability), to take all the material electromagnetic interaction into account
------------ End Original Message ------------

Instruments that are sold for measurement of delta ferrite content actually do measure variations in magnetic permeability. The standards used to calibrate them have their ferrite content determined by metallographic examination. The reason they are called ferrite meters is probably just because ferrite content is the most likely cause of permeability variations is the objects usually tested. This type of instrument is often more useful for testing actual welds or parts than an instrument made to measure magnetic permability of low-permability materials with greater accuracy. The latter have larger probes and require specific sample size, thickness and flatness for highly accurate readings. I have compared both of these types of instruments, a pendulum-type ferrite indicator that "brackets" a sample between two references, and an eddy current tester for a couple of applications. They all agreed with each other for sorting a set of samples with similar geometry.



 
 Reply 
 

Product Spotlight

High-performance Linear Phased Array Probes

Available to order from stock in a range of 5MHz – 7.5MHz and from 16 to 64 elements. Designed w
...
ith piezo-composite elements, Phoenix phased array probes provide high-resolution imaging to maximise sensitivity; accurate ultrasonic detection and sizing of defects in welds; and effective corrosion mapping. Housed in a rugged stainless steel case for on-site industrial NDT applications.
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Ultrasonic Probe Recharacterization Service

NDT Systems offers a comprehensive Aftercare and Recharacterization Service for all our ultrasonic
...
probes. The Recharacterization Service is fully compliant with International ASTM E1065 Standard Guide (and other applicable standards) and offers complete documentation, traceable to the ASTM E1065 Standard. For more details or to schedule Recharacterization Services contact ndtsales@ndtsystems.com
>

FAAST-PA! OEM Patented phased Array for high speed UT inspection

Multiangle, Multifocus, Multifrequency, Multibeam. Instead of stacking UT electronics and having m
...
any PA probes, FAAST-PA is able to transmit all delay laws within ONE single shot in Real time.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window