where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

IMG ULTRASUONI SRL
Ultrasonic transducers for industrial applications (NDT) and medical (Doppler effect). Probes, Ultrasonic instruments, Special systems for NDT.
372 views
Technical Discussions
Simon
Simon
04:39 Jan-09-2007
Computed Radiography

Dear All,

Has anyone used any form of Portable Computed Radiography? More specifically for use as NDT weld inspection in the oil and gas industry. Any advice / criticism / advantages / disadvantages of this type of equipment would be much appreciated. I am particularly interested in the General Electric Industrial Inspection Technologies CR 50P.

Thanks for your time.


 
 Reply 
 
Kari Latvala
Kari Latvala
08:10 Jan-10-2007
Re: Computed Radiography
Hi,
We have had Flat panel technology in use couple years. How ever, we use direct radiography but not CR- plates. There was some items need solved before we got IQI sensitivity within EN requirements, but nowadays it's working wery well.
We have been tested CR- plates also, but systems are allmost as film radiography. Means we need several plates and the plates need reading process after the exposing. Only cemical problems are exclused. The CR- plates need 5- 10 times less radiation dose than films, so exposing times are shorter.
Will be back to the scope

kari


 
 Reply 
 

Product Spotlight

NEW! The PragmaPro Instrument Platform

The PragmaPro is based on a modular cartridge technology and supports various NDT instrument modal
...
ities such as UT, PAUT, ECT and many more. This new platform is based on a machined, powder-coated aluminum frame for shock-proofness, best sealing qualities and maximum heat dissipation. This is practical to extend the outdoor temperature range and/or to extend the power injected in the transducers. The PragmaPro is aiming at a very wide range of applications, such as weld scanning, corrosion mapping and composite testing.
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

Echomac® Small

Available with up to eight channels of electronics to detect and evaluate thickness, flaws and eccen
...
tricity, this UT tester is housed in a convenient, smaller cabinet. This instrument can be used in conjunction with bubbler or immersion tank systems, or with a test bench or in laboratory applications. The Echomac® Small is available in the FD4, FD6 or FD6A versions.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window