where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

PBP Optel sp. z o.o.
Weare searching new ways - in ultrasonic techniques- in creation of new productsUltrasonic instruments - Ultrasonic Testing Card
812 views
Technical Discussions
Paolo
NDT Inspector,
Acciaierie Valbruna, Italy, Joined Nov 2006, 7

Paolo

NDT Inspector,
Acciaierie Valbruna,
Italy,
Joined Nov 2006
7
04:56 Mar-01-2007
ET testing for long products

Does anybody know ET standards for examination of steel long products (es. round bars)?
Thanks
Paolo


    
 
 Reply 
 
Simon Amallraja
Simon Amallraja
09:19 Mar-06-2007
Re: ET testing for long products
----------- Start Original Message -----------
: Does anybody know ET standards for examination of steel long products (es. round bars)?
: Thanks
: Paolo
------------ End Original Message ------------

Contact Mr. Phil Herman Jr @ www.phtool.com and you will get the answer.

Simon


    
 
 Reply 
 
Debdutta Mallik
Consultant,
Malaysia, Joined Jun 2005, 37

Debdutta Mallik

Consultant,
Malaysia,
Joined Jun 2005
37
04:22 Apr-18-2007
Eddy Current Testing for long products
Dear Paolo,
There must be a standard for acceptance criteria of for eddy current testing of your product.If it is a long product then it can be done by online system. What kind of system you have.
For eddy current generally transverse or longitudinal notches are followed for calibration.starting from 0.2 and onwards depending upon the requirement of the specification.I can provide you the information regarding online surface inspection of rails.
Dont hesitate to ask if any further information required.

Best Regards,

Debdutta Mallik


    
 
 Reply 
 
Frank Lund
R & D,
United Kingdom, Joined Apr 2005, 219

Frank Lund

R & D,
United Kingdom,
Joined Apr 2005
219
03:16 Apr-26-2007
Re: Eddy Current Testing for long products
Please see NEWT International's website. I'm sure we can help you.

----------- Start Original Message -----------
: Dear Paolo,
: There must be a standard for acceptance criteria of for eddy current testing of your product.If it is a long product then it can be done by online system. What kind of system you have.
: For eddy current generally transverse or longitudinal notches are followed for calibration.starting from 0.2 and onwards depending upon the requirement of the specification.I can provide you the information regarding online surface inspection of rails.
: Dont hesitate to ask if any further information required.
: Best Regards,
: Debdutta Mallik
------------ End Original Message ------------




    
 
 Reply 
 

Product Spotlight

AMIGO2

TSC Amigo2 - ACFM technology has developed a solid reputation for accurately detecting and sizing
...
surface-breaking cracks through paint and coatings. As the industry demands increased performance in speed, signal quality, and portability, it’s time for an evolution. It’s time for Amigo2.
>

Semi-Automated Phased Array Immersion System for Small Composite Parts

Turn-key semi-automated system as an improved and affordable solution for inspection of small comp
...
osite parts. Includes support table, immersion tank, scanner, PA instrument, PC, Analysis software, database, wedge management and other options.
>

SONOAIR - air-coupled Phased Array Ultrasonic Inspection System

For highly attenuating materials, the performance of the system is critical. The ultrasonic sensors,
...
the scanning area and the system settings should be flexibly adapted to the test task and the material. These high expectations are met with the new and modular testing system SONOAIR. With the world’s first air-coupled phased-array UT inspection system SONOAIR we developed a technology that works with up to 4 transmitter and receiver channels with freely configurable square wave burst transmitters as wells as low noise receiving amplifiers.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window