where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

ACS-Solutions GmbH
develop and manufacture hi-tech devices for Ultrasonic Testing

789 views
Technical Discussions
azhar
azhar
08:54 Mar-11-2007
couplant on hot surface

is there everybody know, can we carry out UT on hot surface temperature about 800 degree celcius,what type of couplant used?


    
 
 
Neil Burleigh
Sales
Krautkramer Australia Pty Ltd, Australia, Joined Dec 2002, 152

Neil Burleigh

Sales
Krautkramer Australia Pty Ltd,
Australia,
Joined Dec 2002
152
02:53 Mar-11-2007
Re: couplant on hot surface
----------- Start Original Message -----------
: is there everybody know, can we carry out UT on hot surface temperature about 800 degree celcius,what type of couplant used?
------------ End Original Message ------------

Hello
What sort of UT do you want to perform defect detection (scanning) or spot thickness testing? This will govern what sort of couplant you will use. Do you have probes to perform these UT tasks?

Regards

Neil Burleigh


    
 
 
Ashish T
Consultant
UNIQUE EVALUATION, India, Joined Feb 2007, 42

Ashish T

Consultant
UNIQUE EVALUATION,
India,
Joined Feb 2007
42
00:47 Mar-13-2007
Re: couplant on hot surface
Dear

We can provide you some Very high temp. couplants. Conatct us.



    
 
 
Mark Potter
Mark Potter
02:28 Mar-14-2007
Re: couplant on hot surface
Depending on how much expense/hassle you want to go to, a laser-EMAT system (laser generator, EMAT reciever) can work at these temperatures, but it would be expensive and not very portable, so more geared to production line than on-site. No couplant would be required in that case.

Mark.


    
 
 

Product Spotlight

FD800 Bench Top Flaw Detectors

The bench-top FD800 flaw detector range combines state-of-the-art flaw detection with advanced mater
...
ial thickness capabilities. Designed for use in the laboratory these gauges are the tool you need for all your flaw detecting needs.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Cygnus 6+ PRO Multi-Mode Ultrasonic Thickness Gauge

The Cygnus 6+ PRO thickness gauge is the most advance gauge within the Cygnus range with key featu
...
res including: comprehensive data logging; A-scan and B-scan display; manual gain control; Bluetooth connectivity; and much more. With its unique dual display and three measuring modes (Multiple-Echo, Echo-Echo and Single-Echo), this surface thickness gauge offers maximum versatility for inspections.
>

TVC awarded UKAS accreditation

TVC are delighted to finally announce we have been awarded UKAS accreditation for our calibration
...
laboratory. Laboratory accreditation to ISO/IEC 17025:2005 enables us to conduct the Electrical Verification of Ultrasonic Flaw Detection Equipment to BS EN 12668-1:2010. It has taken many months of hard work and we want to thank our staff for all their efforts during this massive undertaking.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window
s