where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

PBP Optel sp. z o.o.
We are searching new ways - in ultrasonic techniques - in creation of new products

726 views
Technical Discussions
MUNDA
MUNDA
08:39 May-10-2007
ndt

hello,

any pl. guide me on ut in lieu of rt,our fabrication code asme b.31.1.

also, i would like to inform you all that we welding pipe with pipe fitting i.e. pipe to elbow,tee,reducer etc. thk. between 3 mm to 70 mm.dia between 15 nb to 500 nb & over.material as,cs,ss.
thanks.


    
 
 
Nigel Armstrong
Engineering, - Specialist services
United Kingdom, Joined Oct 2000, 1094

Nigel Armstrong

Engineering, - Specialist services
United Kingdom,
Joined Oct 2000
1094
01:38 May-11-2007
Re: ndt
Hi (Mr) Munda

ASME B31.1 allows UT where t > 19mm. (Table 136.4). You may wish to check with ASME if B31.3 Code Case 181 (Pressure Piping) (Alternative acceptance criteria)has also been issued for B31.1. (Power Piping)

Regards

Nigel

----------- Start Original Message -----------
: hello,
: any pl. guide me on ut in lieu of rt,our fabrication code asme b.31.1.
: also, i would like to inform you all that we welding pipe with pipe fitting i.e. pipe to elbow,tee,reducer etc. thk. between 3 mm to 70 mm.dia between 15 nb to 500 nb & over.material as,cs,ss.
: thanks.
------------ End Original Message ------------




    
 
 
hassan mujadad
hassan mujadad
01:56 May-13-2007
Re: ndt
----------- Start Original Message -----------
: Hi (Mr) Munda
: ASME B31.1 allows UT where t > 19mm. (Table 136.4). You may wish to check with ASME if B31.3 Code Case 181 (Pressure Piping) (Alternative acceptance criteria)has also been issued for B31.1. (Power Piping)
: Regards
: Nigel
: : hello,
: : any pl. guide me on ut in lieu of rt,our fabrication code asme b.31.1.
: : also, i would like to inform you all that we welding pipe with pipe fitting i.e. pipe to elbow,tee,reducer etc. thk. between 3 mm to 70 mm.dia between 15 nb to 500 nb & over.material as,cs,ss.
: : thanks.
------------ End Original Message ------------

for this purpose you will use asme Sec V or table given in ASME B 31.3 table# 136.4 page # 97
this will guide you throughout thichness wise And DIA wise
thanks
Regard,s
Hassan Mujadad


    
 
 

Product Spotlight

GEKKO - Portable Phased Array Testing with TFM in Real-Time

The portable phased array testing system GEKKO provides 64 parallel test channels. On creating testi
...
ng parameters the operator is assisted by the CIVA software. Due to its modular set-up the GEKKO instrument is suitable for operators of all skill levels.
>

35 years of VOGT Ultrasonics!

This year we are celebrating a company anniversary! 35 years have passed since we first took our t
...
est device and swung the probe on behalf of safety. But our ultrasonic know-how goes back many years..
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Digital Radiography for Concrete Inspection

In the construction industry (buildings, bridges) there is a need for fast non- destructive means,
...
most commonly to locate targets (Pipes, Re-bars, Conduit, Fittings etc.) within concrete structures prior to drilling, cutting or coring. Measuring reinforcements is also performed for static calculations and to detect corrosion problems and damages. Cracks and voids can also be visualized. The examinations are not only restricted to concrete constructions; they can also be applied to reinforced masonry made of natural stones or bricks.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window
s