where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

GE Inspection Technologies GmbH
offers equipment, systems and expertise based on ultrasonics, radiography, eddy curreent and remote visual inspection.

731 views
Technical Discussions
Sunny
Sunny
06:03 Jun-21-2007
Inspection of 0.100" O.D bar

Can experienced friend comment on how to inspect such a smaal O.D bar, for surface and internal defects. UT is not easy. ET for surface? Whats best?


    
 
 
Godfrey Hands
Engineering,
PRI Nadcap, United Kingdom, Joined Nov 1998, 287

Godfrey Hands

Engineering,
PRI Nadcap,
United Kingdom,
Joined Nov 1998
287
07:14 Jun-21-2007
Re: Inspection of 0.100" O.D bar
----------- Start Original Message -----------
: Can experienced friend comment on how to inspect such a smaal O.D bar, for surface and internal defects. UT is not easy. ET for surface? Whats best?
------------ End Original Message ------------

Hi Sunny,

Is the bar Ferromagnetic or not?

If it's not, then eddy currents should be OK provided you get the right frequency. Maybe around a few tens of KHz.
If it's Ferromagnetic, then a DC Flux Leakage may be ideal.

Is this a one-off test or for production? If it's one-off and Ferromagnetic, perhaps manual Magnetic Particle Inspection with DC should detect internal defects as well as surface, but you need to ensure your flux is in the right direction for the defects you want to detect.

Regards,

Godfrey Hands




    
 
 
Thomas Vogt
R & D, - -
Guided Ultrasonics Ltd, United Kingdom, Joined Apr 2007, 22

Thomas Vogt

R & D, - -
Guided Ultrasonics Ltd,
United Kingdom,
Joined Apr 2007
22
07:23 Jun-21-2007
Re: Inspection of 0.100" O.D bar
Hi Sunny

As usual, we need more information in order to give an appropriate answer.

What types and size of defects are you looking for? How long is the bar and what material is it?

UT is difficult, but not guided wave UT depending on the above.

Regards,
Tom

----------- Start Original Message -----------
: Can experienced friend comment on how to inspect such a smaal O.D bar, for surface and internal defects. UT is not easy. ET for surface? Whats best?
------------ End Original Message ------------




    
 
 

Product Spotlight

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Digital Radiography for Concrete Inspection

In the construction industry (buildings, bridges) there is a need for fast non- destructive means,
...
most commonly to locate targets (Pipes, Re-bars, Conduit, Fittings etc.) within concrete structures prior to drilling, cutting or coring. Measuring reinforcements is also performed for static calculations and to detect corrosion problems and damages. Cracks and voids can also be visualized. The examinations are not only restricted to concrete constructions; they can also be applied to reinforced masonry made of natural stones or bricks.
>

35 years of VOGT Ultrasonics!

This year we are celebrating a company anniversary! 35 years have passed since we first took our t
...
est device and swung the probe on behalf of safety. But our ultrasonic know-how goes back many years..
>

NEW! The PragmaPro Instrument Platform

The PragmaPro is based on a modular cartridge technology and supports various NDT instrument modal
...
ities such as UT, PAUT, ECT and many more. This new platform is based on a machined, powder-coated aluminum frame for shock-proofness, best sealing qualities and maximum heat dissipation. This is practical to extend the outdoor temperature range and/or to extend the power injected in the transducers. The PragmaPro is aiming at a very wide range of applications, such as weld scanning, corrosion mapping and composite testing.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window
s