where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1241 views
Technical Discussions
David Mackintosh
Engineering,
Acuren Group Inc., Canada, Joined Feb 2011, 85

David Mackintosh

Engineering,
Acuren Group Inc.,
Canada,
Joined Feb 2011
85
00:10 Jul-13-2007
Replicating material for flat-bottom holes

Replication of flat-bottomed holes (FBHs) as per ASTM E127 and E428 was discussed earlier at http://www.ndt.net/wshop/forum/messages-1/11278.html. Can anyone recommend a specific replication material, supplier, or manufacturer?

Thanks,
David Mackintosh


    
 
 Reply 
 
Joe Buckley
Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT, United Kingdom, Joined Oct 1999, 521

Joe Buckley

Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT,
United Kingdom,
Joined Oct 1999
521
00:42 Jul-13-2007
Re: Replicating material for flat-bottom holes
A few of our reps also sell microset replicating materials

http://www.microset.co.uk

I've not used it in anger myself, but their range seems to be pretty well regarded.

Joe


----------- Start Original Message -----------
: Replication of flat-bottomed holes (FBHs) as per ASTM E127 and E428 was discussed earlier at http://www.ndt.net/wshop/forum/messages-1/11278.html. Can anyone recommend a specific replication material, supplier, or manufacturer?
: Thanks,
: David Mackintosh
------------ End Original Message ------------




    
 
 Reply 
 
Charles Truskolasky
Test Examiner Mil-2132, Level III
Lehigh Heavy Forge, USA, Joined Jan 2007, 10

Charles Truskolasky

Test Examiner Mil-2132, Level III
Lehigh Heavy Forge,
USA,
Joined Jan 2007
10
07:11 Jul-16-2007
Re: Replicating material for flat-bottom holes
----------- Start Original Message -----------
: Replication of flat-bottomed holes (FBHs) as per ASTM E127 and E428 was discussed earlier at http://www.ndt.net/wshop/forum/messages-1/11278.html. Can anyone recommend a specific replication material, supplier, or manufacturer?
: Thanks,
: David Mackintosh
------------ End Original Message ------------

Replicating Material- Reprorubber - Thin Pour- Metrology Grade-is an excellant choice and is available from Flexbar Machine Corp., Islandia NY., 11722


    
 
 Reply 
 
Michel
NDT Inspector,
consultant, Canada, Joined Sep 2006, 836

Michel

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
836
04:43 Jul-18-2007
Re: Replicating material for flat-bottom holes
----------- Start Original Message -----------
: : Replication of flat-bottomed holes (FBHs) as per ASTM E127 and E428 was discussed earlier at http://www.ndt.net/wshop/forum/messages-1/11278.html. Can anyone recommend a specific replication material, supplier, or manufacturer?
: : Thanks,
: : David Mackintosh
: Replicating Material- Reprorubber - Thin Pour- Metrology Grade-is an excellant choice and is available from Flexbar Machine Corp., Islandia NY., 11722
------------ End Original Message ------------

I've used dental imprint material in the past with success. The cure time is fearly fast. Can be purchased from a dental supplier or contact your local dentist for the name of his dental supplier.


    
 
 Reply 
 

Product Spotlight

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

MUSE Mobile Ultrasonic Equipment

The MUSE, a portable ultrasonic imaging system, was developed for in-field inspections of light-weig
...
ht structures. The MUSE consists of a motor-driven manipulator, a water circulation system for the acoustic coupling and a portable ultrasonic flaw detector (USPC 3010). The MUSE provides images of internal defects (A-, B-,C- and D-scan).
>

SONOAIR - air-coupled Phased Array Ultrasonic Inspection System

For highly attenuating materials, the performance of the system is critical. The ultrasonic sensors,
...
the scanning area and the system settings should be flexibly adapted to the test task and the material. These high expectations are met with the new and modular testing system SONOAIR. With the world’s first air-coupled phased-array UT inspection system SONOAIR we developed a technology that works with up to 4 transmitter and receiver channels with freely configurable square wave burst transmitters as wells as low noise receiving amplifiers.
>

Echomac® Small

Available with up to eight channels of electronics to detect and evaluate thickness, flaws and eccen
...
tricity, this UT tester is housed in a convenient, smaller cabinet. This instrument can be used in conjunction with bubbler or immersion tank systems, or with a test bench or in laboratory applications. The Echomac® Small is available in the FD4, FD6 or FD6A versions.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window