where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

VOGT Ultrasonics GmbH
non-destructive testing, services, training, ultrasonic systems, immersion and squirter inspection systems, PROline, digital radiology

2062 views
Technical Discussions
AMIRI
Consultant, NDT/QC/WELD INSPECTION
Iran, Joined Nov 2005, 20

AMIRI

Consultant, NDT/QC/WELD INSPECTION
Iran,
Joined Nov 2005
20
05:45 Jul-14-2007
Minimum Thickness for UT

Dear Friends,
What is the minimum effective thickness for UT of welding in pressure vessel by Angle probe (single crystal) and common portable flaw detector?


    
 
 
chris s
chris s
07:50 Jul-17-2007
Re: Minimum Thickness for UT
----------- Start Original Message -----------
: Dear Friends,
: What is the minimum effective thickness for UT of welding in pressure vessel by Angle probe (single crystal) and common portable flaw detector?
------------ End Original Message ------------

What can you prove with your procedure


    
 
 
N.Kuppusamy
Consultant, NDT Level-III Engineer
Advanced Inspection & Testing (S) Pte Ltd, Singapore, Joined Dec 2003, 34

N.Kuppusamy

Consultant, NDT Level-III Engineer
Advanced Inspection & Testing (S) Pte Ltd,
Singapore,
Joined Dec 2003
34
00:09 Jul-28-2007
Re: Minimum Thickness for UT
Please refer ASME Section V, Article-4 and 5.

Practically I limit myself to 10mm as a minimum thickness and I prefer to use 80 degree shear wave probe along with usual 70 degree probe for 10mm thickness.

AWS D1.1 states 8 mm as a minimum thickness and any weld less than that may be tested using specific test procedure established using sufficient number or mock-up welds of same thickness containing anticipated type of defects at various depths.

Regards,



    
 
 
G.Madhesan
G.Madhesan
01:50 Aug-22-2007
Re: Minimum Thickness for UT
Dear Mr.Amiri,
From 8mm you can do UT by angle probe with single crystal.
----------- Start Original Message -----------
: : Dear Friends,
: : What is the minimum effective thickness for UT of welding in pressure vessel by Angle probe (single crystal) and common portable flaw detector?
: What can you prove with your procedure
------------ End Original Message ------------




    
 
 
sivabalan
sivabalan
05:06 Aug-25-2007
Re: Minimum Thickness for UT
Gents,
UT - Make your equipment and your mind equipped before carrying out UT on particular job.
Quantify yourself whether your equipment & setup is capable to test the minimum requirements. for that u have to use calibration blocks, refernce blocks (with refernce to your job u r going to test), make a 1:1 diagram, equip your mind...
now it is practically possible to go for minimum thicknes and even complex geometry UT inspection.
----------- Start Original Message -----------
: : Dear Friends,
: : What is the minimum effective thickness for UT of welding in pressure vessel by Angle probe (single crystal) and common portable flaw detector?
: What can you prove with your procedure
------------ End Original Message ------------




    
 
 
Sanoj J Cruz
Sanoj J Cruz
07:57 Mar-19-2013
Re: Minimum Thickness for UT
In Reply to N.Kuppusamy at 00:09 Jul-28-2007 .

Dear Friends,
Let me know If the welding is fully penitration in 5mm thickness & inspection test plan from client is 100% UT.what is the procedure??? Is MPI enough???..

    
 
 

Product Spotlight

Echomac® PA Rail Wheel Tester

MAC introduces two versions of Rail Wheel Testers using ECHOMAC® PA platform based on customer requ
...
irements.
>

High Resolution Industrial CT System for Small/Medium Size Parts Inspection

The YXLON FF35 CT computed tomography system is designed to achieve extremely precise inspection res
...
ults for a wide range of applications. Available in a single or dual tube configuration, it is perfect for very small to medium size parts inspection in the automotive, electronics, aviation, and material science industries.
>

AIS229 - Multipurpose Real Time System

Latest standard & automatic real time system developed by Balteau. The AIS229 has been designed to
...
do series inspection in a wide variety of industry. Composed of a shielded cabinet, 5 axis manipulator, x-ray generator and tubehead from 160kV to 225kV, a fl at panel & much more, the AIS229 is most certainly one of the most multipurpose RTR system available on the market.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window