where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
896 views
Technical Discussions
Azarov N.T.
Engineering
GosNIIGA, Russia, Joined Jan 2000, 12

Azarov N.T.

Engineering
GosNIIGA,
Russia,
Joined Jan 2000
12
01:22 Jan-18-2000
About materials testing with impact loading


RE: Materials testing with impact loading.
Posted by: Sergei Tsarik , E-mail: sergei.v.tsarik@usa.net, on August 08, 1999 at 10:49:16 :
Hello!
We have developed and have introduced an impact audio method and instrument AUD-01 for a control of strength of wood-shaving plates. I direct to you the prospectus of the instrument.The audio impact flaw detector AUD-01:

The flaw detector is intended for a nondestructive testing of products from nonmetallic materials: aviation constructions from composite materials, wood-shaving plates, plywood and other bonded constructions from wood. Detected imperfections(flaws) - disbond, stratification.
The instrument allows also to inspect by a nondestructive method strength on curving of products from nonmetallic materials, for example, fiberglass, plywood, wood-shaving plates.
In the instrument the audio impact method of a is realized. Difference of the given instrument is the simultaneous registration at once of two parameters of raised impact impulse of free oscillations of the plating: amplitudes "A" and frequency (period " Ò "). It essentially increases a reliability of a control. An apart from it the instrument is small-size, and has both network, and battery power supply.
The instrument has two operational modes: single measurements in isolated points of an inspected product; measurement in separate zones - in 10 points, about representation on indicators of average value of parameters "A" and "Ò" in the given zone. The second method is used for a control strength of the characteristics of products from nonmetallic materials.
The instrument is introduced in production of wood-shaving plates (Russia).

Technical characteristics of the instrument.

Method of energization of oscillations - impact.
Frequency of impacts, Hz - 10-20.
Range of analyzable frequencies, êÃö - 5-500.
Analyzable parameters - amplitude, own frequency of oscillations, fading.
The type of a converter an agent of oscillations of mechanical,impact operation, receiver - piezoelectric.
Indication of data - 2 digital liquid-crystal indicators: amplitudes "" and period "Ò" of oscillations, fading - on the oscillograph connected to an output(exit) of the instrument: single and average value of the inspected parameter on an inspected zone of a product.
Structure of the instrument - electronic block, power supply unit, audio converter.
Power supply of the instrument - battery (9V) and network.
Dimensions, mm - 200x120x180 (electronic block). A mass - 1,5kg (common).


Contact telephones: Moscow, (095) 436-72-72; 391-54-39, Azarov N.T.





    
 
 Reply 
 
Azarov N.T.
Engineering
GosNIIGA, Russia, Joined Jan 2000, 12

Azarov N.T.

Engineering
GosNIIGA,
Russia,
Joined Jan 2000
12
01:24 Jan-18-2000
Re: About materials testing with impact loading
meters of raised impact impulse of free oscillations of the plating: amplitudes "A" and frequency (period " Ò "). It essentially increases a reliability of a control. An apart from it the instrument is small-size, and has both network, and battery power supply.
: The instrument has two operational modes: single measurements in isolated points of an inspected product; measurement in separate zones - in 10 points, about representation on indicators of average value of parameters "A" and "Ò" in the given zone. The second method is used for a control strength of the characteristics of products from nonmetallic materials.
: The instrument is introduced in production of wood-shaving plates (Russia).

: Technical characteristics of the instrument.

: Method of energization of oscillations - impact.
: Frequency of impacts, Hz - 10-20.
: Range of analyzable frequencies, êÃö - 5-500.
: Analyzable parameters - amplitude, own frequency of oscillations, fading.
: The type of a converter an agent of oscillations of mechanical, impact operation, receiver - piezoelectric.
: Indication of data - 2 digital liquid-crystal indicators: amplitudes "" and period "Ò" of oscillations, fading - on the oscillograph connected to an output(exit) of the instrument: single and average value of the inspected parameter on an inspected zone of a product.
: Structure of the instrument - electronic block, power supply unit, audio converter.
: Power supply of the instrument - battery (9V) and network.
: Dimensions, mm - 200x120x180 (electronic block). A mass - 1,5kg (common).

:
: Contact telephones: Moscow, (095) 436-72-72; 391-54-39, Azarov N.T.





    
 
 Reply 
 

Product Spotlight

Ultrasonic Squirter/Gantry System

TecScan’s NDT Ultrasonic Gantry Systems are industrial Squirter scanners designed for non-destru
...
ctive quality testing and raster scanning of large structures and parts. The Gantry Systems are usually composed of an Industrial Mechanical Scanner and a Control Room with System Workstation.
>

TESTD-PT SYSTEM

Pulse thermography is a non-contact test method that is ideal for the characterization of thin fil
...
ms and coatings or the detection of defects. With a remarquable short test time and a high detection sensitivity, the Telops TESTD-PT is the perfect tool for non- destructive testing. With such high frame rates, it is even possible to investigate highly conductive or diffusive materials.
>

FD800 Bench Top Flaw Detectors

The bench-top FD800 flaw detector range combines state-of-the-art flaw detection with advanced mater
...
ial thickness capabilities. Designed for use in the laboratory these gauges are the tool you need for all your flaw detecting needs.
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window