where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1647 views
Technical Discussions
mj
mj
00:49 May-10-2008
Laser optic Tube inspection

Dear friends, i really need your help to sort it out my two problem which iam unknow about it

1. Reformer/Heater Tubes examination using Laser Optic Tube inspection system to detect corrosion/pitting in ID or OD for the use on convention or radiation section.

2. Profile RT using Lixi profile to check insulated or un insulated pipelines for remaning pipethickness,corrosion patern and blockage.

i want your help to sort it out how to get the equipment, manufacture and details about the 2 techniques.

please treat this as URGENT.
thanks


 
 Reply 
 
mkcndt
mkcndt
02:14 May-10-2008
Re: Laser optic Tube inspection
Hi !

Have you considered Ultrasonic tube Inspection System either?

http://www.ndt.net/exhibit/stand/85_ky.htm

mkcndt


 
 Reply 
 
Simon Amallraja
Simon Amallraja
09:19 May-11-2008
Re: Laser optic Tube inspection
----------- Start Original Message -----------
: Dear friends, i really need your help to sort it out my two problem which iam unknow about it
: 1. Reformer/Heater Tubes examination using Laser Optic Tube inspection system to detect corrosion/pitting in ID or OD for the use on convention or radiation section.
: 2. Profile RT using Lixi profile to check insulated or un insulated pipelines for remaning pipethickness,corrosion patern and blockage.
: i want your help to sort it out how to get the equipment, manufacture and details about the 2 techniques.
: please treat this as URGENT.
: thanks
------------ End Original Message ------------

For RT application on insulated or un insulated to check the corrosion, remaining WT of pipe line, check with vidisco Digital Flat Panel System. contact www.vidisco.com. You will get the answer

Simon


 
 Reply 
 
Rich Roberts
Engineering, Executive Managment
Quest Integrity Group, USA, Joined Nov 1998, 78

Rich Roberts

Engineering, Executive Managment
Quest Integrity Group,
USA,
Joined Nov 1998
78
05:28 May-12-2008
Re: Laser optic Tube inspection
Dear Sir,

I would be happy to provide you with full details relating to the use of LOTIS (Laser Optic Tube Inspection System) if you can elaborate on your exact needs. In the mean time, here some key strengths of the technology which you should be aware of:
- laser depth measuring accuracy of +/-0.05mm (0.002”)
- pit diameter resolution accuracy of +/-0.25mm (0.010”)
- capable of inspecting 100% of a 12M (40’) long tube in 2.6 minutes
- Has been applied globally to inspect “both” Heater Coil and Reformer tubes.
- Has been successfully applied to inspect over 150,000 Steam Reformer tubes

Regards, Rich
RichardR@QuestTruTec.com




 
 Reply 
 
S. Jayakumar
S. Jayakumar
21:42 Apr-20-2012
Re: Laser optic Tube inspection
In Reply to Rich Roberts at 05:28 May-12-2008 .

Dear Mr. Robert,
I am Jayakumar from Kuwait, working in a private petrochemical company as T & I Inspector. I would like to know the technical details about the LOTIS method. I took some information from internet which is not clear to my requirement. As part of any internal inspection practice, when you use the specialised technique like ECT, IRIS the tubes to be cleaned throughly to get the exact details to assess the integrity of the tube condition. What about in LOTIS case, do you need through cleaning, if it is so, what type of cleaning required. We need to utilize this new inspection system in our plant for the reactor tubes during the forthcoming shutdown.
Regards,
S.Jayakumar
Kuwait

 
 Reply 
 

Product Spotlight

High-performance Linear Phased Array Probes

Available to order from stock in a range of 5MHz – 7.5MHz and from 16 to 64 elements. Designed w
...
ith piezo-composite elements, Phoenix phased array probes provide high-resolution imaging to maximise sensitivity; accurate ultrasonic detection and sizing of defects in welds; and effective corrosion mapping. Housed in a rugged stainless steel case for on-site industrial NDT applications.
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

Research Center IDEKO develops an ultrasonic train wheel inspection system for CAF

The Basque Research centre IK4-IDEKO has developed a state-of-the-art ultrasonic inspection system f
...
or the train wheel. This system secures a sound condition of train wheels and is thus a significant contribution to rail transport safety. The device was delivered to CAF recently and its use allows the manufacturer to become an approved supplier of rolling stock in Italy, as it meets the demanding homologation standards of this country. \\\\r\\\\n
>

OPBOX with standard software is able to do all types of inspections and measurements: flaw detection in welds and materials, scanning of objects, testing composite materials, forged and moulded pieces, many UT inspections, measurements of properties of ma

Typical applications: UT measurements with pulse technique, Measurement of thicknesses also at hig
...
h temperatures, Measurements of properties of materials, including fluids and gases We are delivering a standard version of the software (for any Microsoft Windows up to 10 x64 with Microsoft Hardware certification report Approved) and for special needs: SDK with ready to use examples for LabView, MATLAB x64, C++ wrapper for dll, Python and Linux., and also low-level description of how to control our devices directly from any USB tools
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window