where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
840 views
Technical Discussions
M.C Macke
NDT Inspector
GE Inspection Services, USA, Joined Aug 2001, 8

M.C Macke

NDT Inspector
GE Inspection Services,
USA,
Joined Aug 2001
8
06:57 Mar-13-2000
Hi Temp thickness of enamle on carbon.

Without touching the piece, it is of major interest to know the
thickness of the enamle coating on cast iron. The maximum thickness
is 3mm. The key is to know this thickness at the initial
solidification temp of 1000f...if there is to little, then he can
add (t), this will help reduce the heating cycles and improve
the Quality control. This system can be assemply line driven if
proven reliable. The problems are 1000f and no contact. Emat is
out, contact required! Mag Lift off...no! UT..2 TO 3 mm at 1000f,
I don't know? Could Infrared be of some help or other optical
method? This one is giving me a hard time of it!!!!




 
 Reply 
 
M. William Moyer
M. William Moyer
07:04 Mar-13-2000
Re: Hi Temp thickness of enamle on carbon.
I saw something recently where laser ultrasonics was used to measure
wet paint thickness. Perhaps it would also work here.


: Without touching the piece, it is of major interest to know the
: thickness of the enamle coating on cast iron. The maximum thickness
: is 3mm. The key is to know this thickness at the initial
: solidification temp of 1000f...if there is to little, then he can
: add (t), this will help reduce the heating cycles and improve
: the Quality control. This system can be assemply line driven if
: proven reliable. The problems are 1000f and no contact. Emat is
: out, contact required! Mag Lift off...no! UT..2 TO 3 mm at 1000f,
: I don't know? Could Infrared be of some help or other optical
: method? This one is giving me a hard time of it!!!!




 
 Reply 
 
Rolf Diederichs
Director,
NDT.net, Germany, Joined Nov 1998, 610

Rolf Diederichs

Director,
NDT.net,
Germany,
Joined Nov 1998
610
06:47 Mar-14-2000
Re: Hi Temp thickness of enamle on carbon.
: Without touching the piece, it is of major interest to know the
: thickness of the enamle coating on cast iron. The maximum thickness
: is 3mm. The key is to know this thickness at the initial
: solidification temp of 1000f...if there is to little, then he can
: add (t), this will help reduce the heating cycles and improve
: the Quality control. This system can be assemply line driven if
: proven reliable. The problems are 1000f and no contact. Emat is
: out, contact required! Mag Lift off...no! UT..2 TO 3 mm at 1000f,
: I don't know? Could Infrared be of some help or other optical
: method? This one is giving me a hard time of it!!!!
----------------

Be carefully by measuring under such hot conditions.
You can get calibration errors of sound velocity, also
the circumferential temperature may not be equal.
There is a company 'MOOG-BUHL AUTOMATION' which supplied
ultrasonic in this field, but measured more down the line.

Rolf



 
 Reply 
 

Product Spotlight

IRIS 9000Plus - Introducing the next generation of heat exchanger inspection.

Representing the seventh generation of the IRIS system, the IRIS 9000 Plus has nearly 200 years of c
...
ombined field inspection experience incorporated in its design. This experience combined with a strong commitment to quality and a history of innovation has made Iris Inspection Services® the undisputed leader in IRIS technology.
>

NDT Master Lecturer

In the program both university professors and practitioners will give lectures, which guarantees the
...
oretical depth and practical inside. Academic Director: Prof. Dr. Christian Boller
The following lecturers are not complete: Prof. Tadeusz Stepinski, Prof. Wieslaw Staszewski, Prof. Frank Walther, Prof. Giovanni Bruno, Prof. Gerd Dobmann, Prof. Philippe Guy
>

SITEX CPSERIES

Teledyne ICM’s CPSERIES has been designed with a view to revolutionizing the handling and perfor
...
mances of portable X-Ray sets. Despite having managed to halve the weight of similar portable X-Ray generators available on the market (while continuing to provide the same power output), the SITEX CPSERIES generators feature a shutter, a laser pointer, a beryllium window, an aluminum filter and two integrated diaphragms (customized sizes are available upon request). Without compromising the robustness and reliability for which ICM products are renowned, the small size and light weight of the SITEX CPSERIES will radically change the way that you perform your RT inspections. And you will see a positive impact in terms of both quality and return on investment (ROI).
>

TraiNDE UT

TraiNDE UT is a virtual tool associated with a signal database which simulates real inspection con
...
ditions for numerous applications (Type A/V1 block, DAC block, welds and plates).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window