where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

514 views
Technical Discussions
UmbertoP
UmbertoP
01:51 Aug-25-2008
UT Calibration block for welds

Hi,

In ASME Section V, 2007 edition, Art. 4 titles "UT examination for welds", while Art. 5 titles "UT examination for materials".
Nonethless, Index at pages 630-631 (2007 edition) reports different titles for Art. 4 and 5;
moreover, in Art. 5 index, pag. 631, it is stated "Basic calibration block (Welds), Art. 5, T-542.2.1". But T-542.2.1 does not exist in 2007 edition.
So, for welds, do I have to use current 2007 edition Cal block indicated in Art. 4, fig. T-434.2.1, or T-542.2.1, which was present in older editions, and is still present in 2007 index edition?


 
 Reply 
 
Iclampers
Iclampers
02:02 Sep-02-2008
Re: UT Calibration block for welds
The Section V 2007 code does not have a fig T542.2.1 anymore. You should check that you do indeed have the current code. There have been quite a few changes to Articles 4 and 5.

If you inspecting welds you have to go by the requirements of Article 4, Article 5 is for materials (ie; castings, forgings, bolts....).


----------- Start Original Message -----------
: Hi,
: In ASME Section V, 2007 edition, Art. 4 titles "UT examination for welds", while Art. 5 titles "UT examination for materials".
: Nonethless, Index at pages 630-631 (2007 edition) reports different titles for Art. 4 and 5;
: moreover, in Art. 5 index, pag. 631, it is stated "Basic calibration block (Welds), Art. 5, T-542.2.1". But T-542.2.1 does not exist in 2007 edition.
: So, for welds, do I have to use current 2007 edition Cal block indicated in Art. 4, fig. T-434.2.1, or T-542.2.1, which was present in older editions, and is still present in 2007 index edition?
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

ISONIC 3510

Very Powerful Superior Performance Extremely Portable Smart Phased Array Ultrasonic Flaw Detector an
...
d Recorder with 2 Conventional UT and TOFD Channels uniquely combines PA, single- and multi-channel conventional UT, and TOFD modalities providing 100% raw data recording and imaging. Suitable for all kinds of every-day ultrasonic inspections
>

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

VOGT Ultrasonics awarded innovation champion

Let go of the old and try something new. VOGT convinced the jury in the 27th round of the TOP 100
...
innovation competition. Our team is very pleased to officially belong to the TOP 100 in Germany!
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window