where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Ultrasonic Sciences Ltd
We specialize in the design and manufacture of automated and semi-automated ultrasonic testing systems, including multi axis, multi channels systems and phased array electronics.

810 views
Technical Discussions
balwinder singh
balwinder singh
09:55 Nov-30-2008
Selection of IQI/Radition source

dear experts,

we are doing radiographic testing of piping weldments,the dimension of our job as detail given below:-

OD OF PIPE/Single wall thickness

141/6.55 mm
168.3/7.11 mm

class of testing EN 1435 CLASS B

question is:-
what type of source we have to used.

which wire should be vissible on radiograph.(IQI 10 10 FE EN).

also let me know what is penetrated thickness.
thanks



    
 
 
Nigel Armstrong
Engineering, - Specialist services
United Kingdom, Joined Oct 2000, 1096

Nigel Armstrong

Engineering, - Specialist services
United Kingdom,
Joined Oct 2000
1096
01:56 Dec-01-2008
Re: Selection of IQI/Radition source
Balwinder

Contract documentation should specify if there are any limitations further than the moninated Code. So the Owner's specification may say "X-ray only", even though the Codes usually permit either X or gamma within material thickness limitations. Low kV X-ray gives better images in most cases than commercially available gamma sources, though I have read that Selenium can give good results on thinner materials.

Your required visible wire is one that indicates better then 2% sensitivity so its diameter should be less than 6.55mm x 0.02 = 0.131mm or 7.11mm x 0.02 = 0.142mm

Penetrated thickness for Ug unsharpness calculation is the single wall thickness (6.55 or 7.11mm) + single measured weld reinforcement.

Hope this helps

Nigel

----------- Start Original Message -----------
: dear experts,
: we are doing radiographic testing of piping weldments,the dimension of our job as detail given below:-
: OD OF PIPE/Single wall thickness
: 141/6.55 mm
: 168.3/7.11 mm
: class of testing EN 1435 CLASS B
: question is:-
: what type of source we have to used.
: which wire should be vissible on radiograph.(IQI 10 10 FE EN).
: also let me know what is penetrated thickness.
: thanks
------------ End Original Message ------------




    
 
 
annonym
annonym
07:59 Dec-01-2008
Re: Selection of IQI/Radition source
Selen 75, Wire 13 or 14 should be visible.

----------- Start Original Message -----------
: Balwinder
: Contract documentation should specify if there are any limitations further than the moninated Code. So the Owner's specification may say "X-ray only", even though the Codes usually permit either X or gamma within material thickness limitations. Low kV X-ray gives better images in most cases than commercially available gamma sources, though I have read that Selenium can give good results on thinner materials.
: Your required visible wire is one that indicates better then 2% sensitivity so its diameter should be less than 6.55mm x 0.02 = 0.131mm or 7.11mm x 0.02 = 0.142mm
: Penetrated thickness for Ug unsharpness calculation is the single wall thickness (6.55 or 7.11mm) + single measured weld reinforcement.
: Hope this helps
: Nigel
: : dear experts,
: : we are doing radiographic testing of piping weldments,the dimension of our job as detail given below:-
: : OD OF PIPE/Singlewall thickness
: : 141/6.55 mm
: : 168.3/7.11 mm
: : class of testing EN 1435 CLASS B
: : question is:-
: : what type of source we have to used.
: : which wire should be vissible on radiograph.(IQI 10 10 FE EN).
: : also let me know what is penetrated thickness.
: : thanks
------------ End Original Message ------------




    
 
 

Product Spotlight

AMIGO2

TSC Amigo2 - ACFM technology has developed a solid reputation for accurately detecting and sizing
...
surface-breaking cracks through paint and coatings. As the industry demands increased performance in speed, signal quality, and portability, it’s time for an evolution. It’s time for Amigo2.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

SONOAIR - air-coupled Phased Array Ultrasonic Inspection System

For highly attenuating materials, the performance of the system is critical. The ultrasonic sensors,
...
the scanning area and the system settings should be flexibly adapted to the test task and the material. These high expectations are met with the new and modular testing system SONOAIR. With the world’s first air-coupled phased-array UT inspection system SONOAIR we developed a technology that works with up to 4 transmitter and receiver channels with freely configurable square wave burst transmitters as wells as low noise receiving amplifiers.
>

CIVA 2017 UT Module

CIVA NDE Simulation Software is the world leader of NDT Simulation. The UT simulation Module incl
...
udes: - "Beam computation": Beam propagation simulation - "Inspection Simulation": Beam interaction with flaws or specimens The user can simulate a whole inspection process (pulse echo, tandem or TOFD) with a wide range of probes (conventional, Phased- arrays or EMAT), components, and flaws.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window