where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

GB Inspection Systems Ltd.
A leading UK manufacturer of Ultrasonic Probes, Accessories, Supplier of NDT Equipment and more.
222 views
Career Discussions
S.Thomson
S.Thomson
09:22 Jun-04-2003
quiz qeustion queries

I need some conformation on some questions.

Q1 Standing waves are generated in ut testing for
a. B-scans
b. through testing
c. resonance thickness testing
d. flaw detection

Q2 Touching the reflection point of a normally incident transverse wave with an oily finger will
a. reduce signal by about 6dB
b. increase the signal by about 2dB
c. reduce the signal by about 2dB
d. have no effect on the signal

Q3 The result of increasing the temp from 10deg C to 30 deg C is
a. decrease the refracted angle
b. decrease the acoustic velocity
c. increase sensitivity
d. all of the above

Q4 The unit of sound (or electrical energy) gain or attenuation , dB is
a. a ratio of voltages or intencities
b. one tenth of a bell
c. both a and b

Q5 Non contact ultrasonic coupling , ie coupling across an air gap has its advantage in
a. testing at elevated temperatures is possible
b. avoiding trasducer wear on rough surfaces
c. avoiding fluid contamination of test piece
d. all of the above

Q6 An advantage of using ut surface waves over other wave modes is
a. the ease of focusing the beam
b. test piece contours are followed without loss of due to direction changes
c. good sensitivity to subsurface defects
d. none of the above

Q7 In snells law there will be no first criticle angle if the
a. acoustic impedance of the refracting medium is greater than 1
b. acoustic velocity in the refracting medium is less than in the incident medium
c. incident angle does not exceed 89 degrees
d. none of the above there will always be a first critical angle





    
 
 Reply 
 

Product Spotlight

EKOSCAN Phased Array

In order to always fit your needs, EKOSCAN can manufacture any type of UT transducer, either convent
...
ional or Phased Array. As an ISO 9001: 2015 certified company, EKOSCAN is extremely careful as far a material selection and manufacturing processes are concerned. Our probes guarantee our customers the benefits of latest innovations regarding piezo-composite, backing, impedance adaptation layer, etc. Specific probes for hostile environment: high temperature, high pressure, corrosive environment,etc. Specific probes designed to fit your specific application: optimization of every parameter to guarantee you the best detection.
>

Conformable wedge transducer

The conformability is obtained with a flexible membrane filled with water between the transducer and
...
the inspected component. The coupling between the membrane and the component requires a small quantity of water or couplant. The conformable wedge combines the acoustic performance of immersion technique with good coupling and low attenuation.
>

NovaScope 6000

The all-digital Novascope 6000 is a portable, ultra-high precision thickness gauge for high-speed
...
thickness measurement. Novascope 6000 has unmatched capabilities and unique features including: •Superior Resolution with high contrast, high-speed color RF display •High pulser voltage •Real-time video output •Increased internal/external data storage •Programmable SetUp features •Battery & AC Powered
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window