where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1334 views
Career Discussions
Jiri Brus
Jiri Brus
00:42 Mar-01-2005
Interlaboratory comparison in NDT area

Dear NDT managers,
can anybady help me to solve problem with
interlaboratory comparison test in NDT area ?
Does anybody do somthink like that ?
What can be a result, if nondestructive testing
is allowed to be nonquantitative method ?
Thank you


    
 
 Reply 
 
N.Kuppusamy
Consultant, NDT Level-III Engineer
Advanced Inspection & Testing (S) Pte Ltd, Singapore, Joined Dec 2003, 34

N.Kuppusamy

Consultant, NDT Level-III Engineer
Advanced Inspection & Testing (S) Pte Ltd,
Singapore,
Joined Dec 2003
34
00:31 Mar-02-2005
Re: Interlaboratory comparison in NDT area
----------- Start Original Message -----------
Hi,
We do it in Singapore as part of our accreditation program. We compare only result (such as type of defect, length, location, Accept or reject & procedure) within mutually acceptable error margin.

If there is unacceptable variation in test result. All representatives (mostly Level-III or designated person by the company) from participating laboratories meet and discuss the problem, find out the source of error, then come out with a set of rules to prevent such deviations in future.

Please tell about your problem, because it should be approached case by case basis.

Regards,
N.Kuppusamy
: Dear NDT managers,
: can anybady help me to solve problem with
: interlaboratory comparison test in NDT area ?
: Does anybody do somthink like that ?
: What can be a result, if nondestructive testing
: is allowed to be nonquantitative method ?
: Thank you
------------ End Original Message ------------




    
 
 Reply 
 
djciric
djciric
13:15 Feb-10-2012
Re: Interlaboratory comparison in NDT area
In Reply to Jiri Brus at 00:42 Mar-01-2005 (Opening).

Dear, as I know ILC can so by providers - see link:

http://www.eptis.bam.de/en/index.htm


Regards

    
 
 Reply 
 
Marco Casaril
NDT Inspector,
OMECO SRL Research Centre - Material Testing - Calibration, Italy, Joined Jan 2010, 10

Marco Casaril

NDT Inspector,
OMECO SRL Research Centre - Material Testing - Calibration,
Italy,
Joined Jan 2010
10
08:22 Feb-11-2012
Re: Interlaboratory comparison in NDT area
In Reply to Jiri Brus at 00:42 Mar-01-2005 (Opening).

You can find some Interlaboratory test programs at IFEP:

http://proficiencytest.eu/dokumente2012/Info_EN_Met_2012%202011-10-14%20Form.pdf

http://proficiencytest.eu/dokumente2011/Info_EN_Met_2011%202011-07-04%20Form.pdf

Regards
Marco Casaril

    
 
 Reply 
 

Product Spotlight

Teletest Focus+

Teletest Focus+ electronics have superior capabilities than rivals on the market. Beyond the usual
...
test features, Focus+ has 24 transmit channels and 24 receive channels, with an additional on-board switching capabilities. The instrument's frequency range is 10–300 kHz.
>

TESTD-PT SYSTEM

Pulse thermography is a non-contact test method that is ideal for the characterization of thin fil
...
ms and coatings or the detection of defects. With a remarquable short test time and a high detection sensitivity, the Telops TESTD-PT is the perfect tool for non- destructive testing. With such high frame rates, it is even possible to investigate highly conductive or diffusive materials.
>

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

Compact NDT inspection-heads for measurements with active thermography

The compact inspection head is suitable for thermographic ndt tasks. The uncooled infrared camera
...
is specially developed for NDI-tasks and offers a thermal sensitivity until now known only from thermal imagers with cooled detector. All required components and functions are integrated into the inspection-head. You will only need an ethernet cable to connect the sensor with the evaluation system.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window