where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
2151 views
Career Discussions
john bisceglia
john bisceglia
06:27 Apr-04-2006
microdot bnc connectors

I would like to make my own microdot to bnc cables for ultrasonic inspection. Does anybody know where i could get the crimping tool necessary to make these connections


 
 Reply 
 
Linas Svilainis
R & D,
Kaunas University of Technology, Lithuania, Joined Nov 1998, 67

Linas Svilainis

R & D,
Kaunas University of Technology,
Lithuania,
Joined Nov 1998
67
04:16 Apr-05-2006
Re: microdot bnc connectors
----------- Start Original Message -----------
: I would like to make my own microdot to bnc cables for ultrasonic inspection. Does anybody know where i could get the crimping tool necessary to make these connections
------------ End Original Message ------------

Up to my knowledge microdot can be assembled without crimping (refer to AMP instruction sheet 408-8521 former RF-ASMB-88). I used manual pressfitting using a simpte screw.
The other brand I know is KY-017 KY-018. I only have a pictures - I think the RG174 cable shloud be used here. So, RG174 crimp tool should do.




 
 Reply 
 
Rob with(tuboscope)
Rob with(tuboscope)
05:48 Apr-13-2007
Re: microdot bnc connectors
----------- Start Original Message -----------
: : I would like to make my own microdot to bnc cables for ultrasonic inspection. Does anybody know where i could get the crimping tool necessary to make these connections
: Up to my knowledge microdot can be assembled without crimping (refer to AMP instruction sheet 408-8521 former RF-ASMB-88). I used manual pressfitting using a simpte screw.
: The other brand I know is KY-017 KY-018. I only have a pictures - I think the RG174 cable shloud be used here. So, RG174 crimp tool should do.
------------ End Original Message ------------

http://www.usultratek.com/products/connectors.htm



 
 Reply 
 
Joe Buckley
Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT, United Kingdom, Joined Oct 1999, 526

Joe Buckley

Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT,
United Kingdom,
Joined Oct 1999
526
02:40 Apr-13-2007
Re: microdot bnc connectors

It depends what you are using them for, If its a static connection then its not too critical. If the connector is being flexed a lot (as it would if you have it on a UT Probe) then optimal crimping /strain relief makes a lot of difference to how long the assembly lasts. (using the wrong tool can greatly reduce the connection strength) I presume you want to make your own cables up to save costs, If you are replacing them more often that may prove a false economy.

You might want to look at the compatible connectors from Microtech

http://www.mmm-microtech.com/BSeries.htm

They aren't quite as robust as the full military spec microdots, but they are (or used to be, its been a while) a lot cheaper and easier to use.

Joe


----------- Start Original Message -----------
: : : I would like to make my own microdot to bnc cables for ultrasonic inspection. Does anybody know where i could get the crimping tool necessary to make these connections
: : Up to my knowledge microdot can be assembled without crimping (refer to AMP instruction sheet 408-8521 former RF-ASMB-88). I used manual pressfitting using a simpte screw.
: : The other brand I know is KY-017 KY-018. I only have a pictures - I think the RG174 cable shloud be used here. So, RG174 crimp tool should do.
: http://www.usultratek.com/products/connectors.htm
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

GEKKO - Portable Phased Array Testing with TFM in Real-Time

The portable phased array testing system GEKKO provides 64 parallel test channels. On creating testi
...
ng parameters the operator is assisted by the CIVA software. Due to its modular set-up the GEKKO instrument is suitable for operators of all skill levels.
>

Research and Applications Development For NDT

The Research and Applications Development (RAD) group is a newly formed team within Acuren dedicat
...
ed to tackling challenging inspection problems. Our focus is the development of novel, field deployable, advanced inspection techniques for use in cases where standard NDT methods are ineffective. We don't wait for new innovations, we engineer them. From concept to commissioning.
>

EKOSCAN Phased Array

In order to always fit your needs, EKOSCAN can manufacture any type of UT transducer, either convent
...
ional or Phased Array. As an ISO 9001: 2015 certified company, EKOSCAN is extremely careful as far a material selection and manufacturing processes are concerned. Our probes guarantee our customers the benefits of latest innovations regarding piezo-composite, backing, impedance adaptation layer, etc. Specific probes for hostile environment: high temperature, high pressure, corrosive environment,etc. Specific probes designed to fit your specific application: optimization of every parameter to guarantee you the best detection.
>

IntraPhase Athena Phased Array System

The Athena Phased Array system, manufactured by WesDyne NDE Products & Technology, consists of a pha
...
sed array acquisition system and PC running IntraSpect software. A PC is used to perform acquisition, analysis and storage of the data. System hardware is capable of operating up to four data sets with any combination of phased array or conventional UT probes. NOW AVAILABLE IN 64-64 CONFIGURATION.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window