where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
2115 views
Career Discussions
Bobby
Bobby
05:36 Feb-27-2007
Selenium 75

Hi all looking to make expsoure with Selenium 75 useing Agfa D 3 and can not find r factors for any film I have 2'' 6''x500 and 8'' x.719,12''x.500 any help would be aperseated


 
 Reply 
 
Buddy Butcher
Buddy Butcher
06:03 Mar-01-2007
Re: Selenium 75
Try this link. It's from NDT.net

http://www.ndt.net/article/apcndt2006/papers/12.pdf


----------- Start Original Message -----------
: Hi all looking to make expsoure with Selenium 75 useing Agfa D 3 and can not find r factors for any film I have 2'' 6''x500 and 8'' x.719,12''x.500 any help would be aperseated
------------ End Original Message ------------




 
 Reply 
 
Scott Cargill
Scott Cargill
05:43 Nov-29-2007
Re: Selenium 75
----------- Start Original Message -----------
: Try this link. It's from NDT.net
: http://www.ndt.net/article/apcndt2006/papers/12.pdf
:
: : Hi all looking to make expsoure with Selenium 75 useing Agfa D 3 and can not find r factors for any film I have 2'' 6''x500 and 8'' x.719,12''x.500 any help would be aperseated
------------ End Original Message ------------


R factor for the film won't change no matter what source you use.

We're looking at Se75 now, best I can tell figure on 2.2 R per hour at 1 foot and go for it. Ie Double your Ir192 shot time and you should be close.



 
 Reply 
 

Product Spotlight

32:128PR PAUT & 2-ch TOFD Flaw Detector: SyncScan 2

●32:128PR PAUT with optional 2-ch TOFD to maximize your efficiency ●Support PR mode for corrosi
...
on inspection ●Multiple solutions for welds & corrosion ●Faster scan speed (Approximately 3 meters/minute) ●Light weight: 4kg only including battery
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

On-Demand Webinar: Advanced Ultrasonic Techniques for HTHA Detection & Assessment

In the Oil and Gas industry, High Temperature Hydrogen Attack (HTHA) can occur in steels operating a
...
t high temperature, usually above 205°C (400°F). Early stages of HTHA are very difficult to detect. Join us for a webinar presented by Guy Maes, Zetec Sales Engineer Director. The webinar will demonstrate how advanced ultrasonic techniques are deployed for efficient and reliable HTHA inspections.
>

Echomac® PA Bar Tester

The Echomac® PA BT provides 100% inspection of round bars for core and surface defects, at speeds u
...
p to 2 m/sec, depending on the specific application. The unit allows producers to handle a much larger range of diameters in one installation, and is available in 3 models to test 10 – 75mm diameter (small model); 20 – 130mm (medium model) or 50 – 254mm (large model) bars.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window