where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1042 views
Career Discussions
L. D. Sapkota
Director,
Venus Inspection & QCS Pvt. Ltd., Nepal, Joined Oct 2008, 9

L. D. Sapkota

Director,
Venus Inspection & QCS Pvt. Ltd.,
Nepal,
Joined Oct 2008
9
04:00 Oct-21-2008
transfaring the certificate

Now I have ASNT level II( RT, UT, MT, PT) certificate. I want to transfer or equivalent my certificate ASNT to ISO9712 or EN473. Could you please advice me.




 
 Reply 
 
Nigel
Engineering, - Specialist services
United Kingdom, Joined Oct 2000, 1096

Nigel

Engineering, - Specialist services
United Kingdom,
Joined Oct 2000
1096
04:01 Oct-21-2008
Re: transfaring the certificate
Hello Mr Sapokta

You call your certificates ASNT level II - do you mean they are issued in accordance with recommended practice SNT-TC-1A, i.e. employer-based cetification issued by the company-approved Level III. Or do you mean ACCP central certification, or CP 189?

ISO or EN NDT personnel certification is issued once the candidate has met ALL the requirements including training hours at an approved training establishment, documented minimum experience and successful completion of their stipulated examinations at an authorised test centre (amongst other things).

My best advice to you is to contact your nearest authorised test centre with all your records leading to certification - training certificates, exam results etc and ask them what they advise. If dual EN/SNT certification is required its usual to organise this before gaining individual certification in order to ensure meeting both sets of requirements in the most efficient and cost-effective way.

Good luck.

Nigel

----------- Start Original Message -----------
: Now I have ASNT level II( RT, UT, MT, PT) certificate. I want to transfer or equivalent my certificate ASNT to ISO9712 or EN473. Could you please advice me.
------------ End Original Message ------------




 
 Reply 
 
Oliviero Oldani
NDT Inspector,
Quality Control srl, Italy, Joined Oct 2008, 414

Oliviero Oldani

NDT Inspector,
Quality Control srl,
Italy,
Joined Oct 2008
414
00:56 Oct-21-2008
Re: transfaring the certificate
----------- Start Original Message -----------
: Now I have ASNT level II( RT, UT, MT, PT) certificate. I want to transfer or equivalent my certificate ASNT to ISO9712 or EN473. Could you please advice me.
------------ End Original Message ------------

To obtain the EN473 end/or ISO9712 certification You need to ask to a Certification Organization and their Examination Center operating everywhere, submit the application and perform an examination.
Also ASNT can examine according to their ACPP system which born to satisfy the ISO 9712 requirments.


 
 Reply 
 

Product Spotlight

IntraPhase Athena Phased Array System

The Athena Phased Array system, manufactured by WesDyne NDE Products & Technology, consists of a pha
...
sed array acquisition system and PC running IntraSpect software. A PC is used to perform acquisition, analysis and storage of the data. System hardware is capable of operating up to four data sets with any combination of phased array or conventional UT probes. NOW AVAILABLE IN 64-64 CONFIGURATION.
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

AIS229 - Multipurpose Real Time System

Latest standard & automatic real time system developed by Balteau. The AIS229 has been designed to
...
do series inspection in a wide variety of industry. Composed of a shielded cabinet, 5 axis manipulator, x-ray generator and tubehead from 160kV to 225kV, a fl at panel & much more, the AIS229 is most certainly one of the most multipurpose RTR system available on the market.
>

Conformable wedge transducer

The conformability is obtained with a flexible membrane filled with water between the transducer and
...
the inspected component. The coupling between the membrane and the component requires a small quantity of water or couplant. The conformable wedge combines the acoustic performance of immersion technique with good coupling and low attenuation.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window