where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Canadian Institute for NDE
We are specialized in training for Radiography, Ultrasonics, Magnetic Particle, Liquid Penetrant, Eddy Current and emerging NDT technologies.
203 views
Job Offers
JHill
Director, Field Operations
IMAC, USA, Joined Jun 2008, 4

JHill

Director, Field Operations
IMAC,
USA,
Joined Jun 2008
4
04:43 Jun-16-2008
NDT Level III MT

Job Location: MI, USA
offered by  

THIS POSITION IS OPEN TO U.S. CITIZENS ONLY DUE TO THE CONTRACTORS ASSOCIATION WITH THE DEPARTMENT OF DEFENSE. I have an opening for a temporary position: NDT Level III MT Specialist. The job is slated to start at the beginning of July, 2008. The position would require crossing a picket line during a labor dispute. The job details are as follows:
Position Summary: The NDT Level III Specialist reports to the Quality Leader and is responsible for the day-to-day technical support for all nondestructive testing. This individual will apply the NDT technologies of Magnetic Particle Inspection (MT). This individual will work in concert with the Quality Leader to provide the overall technical leadership and future development direction for Nondestructive Evaluation at our client's facility.
· Will make final determination on acceptability of questionable hardware found by the NDT process, maintain all necessary documentation of the controls of the NDT processes, including their solutions and equipment.
·Will develop, update and institute NDT procedures and work instructions as required for existing equipment and implement new NDT inspection equipment, including necessary capability studies, procedures, work instructions and inspector training.
Position Requirements: The position requires a NDT level III MT certification.
Compensation: Hourly rate of $25.00. Perdiem $35.00 a day. Housing provided. Will be working 7 days a week 12 hours per day. Reply by email for consideration.


 
 

Product Spotlight

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

YXLON Cougar EVO

Scalable small footprint X-ray inspection systems for assembly and laboratory applications. The
...
YXLON Cougar EVO series was designed to provide the "best-in- class" inspection solutions for SMT, semiconductor, and laboratory assembly applications, while maintaining a small system footprint for maximum convenience. With optimized software and hardware, these systems produce higher quality and more consistent results than other electronics inspection systems currently on the market.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window